"an " CNS Standards List |
|
CNS 13623
2017 Edition Test Methods for Measuring Resistivity,Hall Coefficient and Determining Hall Mobility in Single-Crystal Semiconductors(Van Der Pauw Method) 單晶片之電阻率、霍爾係數及霍爾移動率之測定法（范德普法） |
|
|
|
CNS 14798
2017 Edition The performance requirements for disposable medical protective clothing 拋棄式醫用防護衣―性能要求 |
|
|
|
CNS 506
2017 Edition ISO Metric Fine Screw Threads (Diameters from 70 to 300 mm and Pitch 6 mm) 公制細螺紋9（ISO制）（標稱直徑70至300公釐，螺距6公釐） |
|
|
|
CNS 13214
2017 Edition Basic Environmental Testing Procedures Part 2: Tests – Test Ec: Drop and Topple, Primarily for Equipment - type Specimens 環境試驗法（電氣、電子）–面落下、角落下及翻倒（主要為設備）試驗法 |
|
|
|
CNS 10124
2017 Edition Method for Determining Sulphur Content in Natural and Artificial Cryolite and Aluminium Fluoride for Industrial Use (X-Ray Fluorescence Spectrometric Method) 天然及人造冰晶石與工業用氟化鋁中硫定量法（Ｘ射線螢光光譜分析法） |
|
|
|
CNS 1132
2017 Edition Pliers and nippers - Diagonal cutting nippers 夾鉗與剪鉗－對口剪鉗（平口鉗） |
|
|
|
CNS 4856
2017 Edition Fixed capacitors for use in electronic equipment (Aluminium electrolytic capacitors with solid and non-solid electrolyte) 電子設備用鋁質電解電容器（固體及非固體電解質） |
|
|
|
CNS 15235
2017 Edition Methods of accelerated cyclic corrosion resistance tests for anodic coatings with exposure to salt spray, dry and wet conditions 陽極被覆鋼板之加速循環腐蝕試驗法 |
|
|
|
CNS 11329
2017 Edition Test Method for the Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
|
|
|
CNS 13350-1
2017 Edition The Safety Code of Mechanical Parking Lot Devices (Vertical Circulating Type) 機械式停車場安全標準（垂直循環式停車裝置） |
|
|
|
CNS 4047
2017 Edition Copper beryllium alloy, phosphor bronze and nickel silver rods, bars and wires 鈹銅、磷青銅及鎳銀之棒及線 |
|
|
|
CNS 4369
2017 Edition Round Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal Sizes 圓螺紋（具有間隙、淺螺腹，螺距為７ｍｍ之標稱尺寸） |
|
|
|
CNS 9111
2017 Edition Symbols of Lamp and Socket of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電燈、插座類符號 |
|
|
|
CNS 11574
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-51 Ice Resistance of Mated Connectors Test) 頻率３ＭＨｚ以下電連接器檢驗法（配對連接器之抗冰試驗ＴＰ–５１） |
|
|
|
CNS 4367
2017 Edition Knuckle Threads for Steel Sheet pieces (up to 0.5 mm Thickness and Appropriated Couplings Dimensions Tolerances) 圓螺紋（厚0.5mm以下之鋼皮製品及其 配合螺紋） |
|
|
|
CNS 15420
2017 Edition Office furniture - Desks and tables 辦公室用桌 |
|
|
|
CNS 2060
2017 Edition Ventilating Fan 通風電扇 |
Translated |
|
|
CNS 5274
2017 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 6414
2017 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條（一般機械及重機械用） |
|
|
|
CNS 13092
2017 Edition Measuring Method for LED Outdoor Display Panels 發光二極體顯示幕（戶外用）量測法 |
|
|
|
CNS 713
2017 Edition Cast iron flanged gate valves (10 kgf/㎠) (Inside screw non-rising stem type) 鑄鐵凸緣型閘閥（10 kgf/㎠）（閥桿非上升型） |
Translated |
|
|
CNS 2178
2017 Edition Liquid Membrane-Forming Compounds for Curing Concrete 混凝土用液膜養護劑 |
Translated |
|
|
CNS 14140
2017 Edition Reliability and lot control tests for transmitter and receiver modules used for wireless infrared communication 無線通信用紅外線傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 5268
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 513
2017 Edition Metric Trapezoidal Screw Threads Allowance and Tolerances for General Purpose Trapezoidal Screw Threads 梯形螺紋（一般用梯形螺紋的裕度及公差） |
|
|
|
CNS 9267
2017 Edition Method of mass calculation for stainless steel plates and sheets,and heat-resisting steel plates and sheets 不銹鋼及耐熱鋼鋼板及鋼片質量計算法 |
|
|
|
CNS 11446-1
2017 Edition Method of measurement on receives for television broadcast transmission - Part 1: General considerations - Measurements at radio and video frequencies 電視廣播傳輸接收機之量測方法-第一部:概論-射頻及視頻之量測 |
|
|
|
CNS 10442
2017 Edition Copper and copper alloy rods and bars 銅及銅合金棒 |
|
|
|
CNS 62841-1
2017 Edition Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 1: General requirements 手持型、可移置型電動工具及草坪與園藝用機械－安全性－第1部：通則 |
|
|
|
CNS 9504
2017 Edition Methods for estimating average grain size of wrought copper and copper alloys 銅及銅合金展伸材料之晶粒尺度測定法 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [150] [151] [152] [153] [154] [155] [156] |
