"2, " CNS Standards List |
|
CNS 172
2017 Edition Woodruff Keys 半圓鍵 |
|
|
|
CNS 4442
2017 Edition Oil Tempered Carbon Steel Wires for Springs 彈簧用油回火碳鋼鋼線 |
Translated |
|
|
CNS 3424
2017 Edition Varnished Cotton Bias Tape 漆斜條棉布帶 |
|
|
|
CNS 4402
2017 Edition Toothed Lock Washers 有齒墊圈 |
|
|
|
CNS 227
2017 Edition 60° Center Drills,Straight Form 中心鑽(60°,直線錐形) |
Translated |
|
|
CNS 12519
2017 Edition Metal Spectacle Frames 金屬眼鏡架 |
|
|
|
CNS 12336
2017 Edition Multi-wrenches 萬能扳手 |
|
|
|
CNS 12288
2017 Edition General Rules for Reliability Assured Fixed Metal Film Resistors 可靠度保證金屬皮膜固定電阻器總則 |
|
|
|
CNS 10642
2017 Edition Straight Lip, Flat, Blacksmiths' Tongs 鍛工用直口扁平夾鉗 |
|
|
|
CNS 236
2017 Edition 75° Countersink Drill 75°沉鑽頭 |
Translated |
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用25–947MHz調頻/調相接收機檢驗法(聲頻響應、諧波失真因數、交流聲及雜訊) |
|
|
|
CNS 14592
2017 Edition Molybdenum steel and chromium molybdenum steel covered electrodes 鉬鋼及鉻鉬鋼用被覆銲條 |
|
|
|
CNS 13652
2017 Edition Reliability Testing for Light Emitting Diode(for Communication) 通信用發光二極體之可靠度測試 |
|
|
|
CNS 12106
2017 Edition Method of Test for Water Absorbency of Bibulous Paper -- Absorption Rate Method 高吸水性紙吸水性試驗法–吸水速率法 |
Translated |
|
|
CNS 13622
2017 Edition Fixed chip resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 7962
2017 Edition Test Code for Performance of Numerically Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 5266
2017 Edition Series of Modules for Worm Gear Pairs 齒輪模數(蝸桿蝸輪對) |
|
|
|
CNS 9562
2017 Edition Testbar for Automatic Lathes 自動車床之檢驗試棒 |
|
|
|
CNS 4424
2017 Edition Cup Square Bolts, Metric Thread, Regular 杯頭方頸螺栓(粗製) |
|
|
|
CNS 2952
2017 Edition Sampling of pulps for testing 試驗用紙漿之取樣法 |
|
|
|
CNS 12548
2017 Edition Method of Shear Test for Side Fillet Welded Joint 側面填角熔接接合之剪切試驗法 |
|
|
|
CNS 12338
2017 Edition Crowbars 撬桿 |
|
|
|
CNS 5274
2017 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪(齒跨距數值表) |
|
|
|
CNS 12337
2017 Edition Pliers for radio ( replaced by CNS 1137 ) 扣環鉗 |
|
|
|
CNS 302
2017 Edition Hand Tap, Metric 公制絲公,手用 |
Translated |
|
|
CNS 15552
2017 Edition Packaging - Accessible design - General requirements 包裝-無障礙設計 - 一般要求 |
|
|
|
CNS 12849
2017 Edition Nodular Graphite Iron Flanged Globe Valves (10 kgf/㎠) 球狀石墨鑄鐵凸緣球形閥(10 kgf/㎠) |
Translated |
|
|
CNS 11112
2017 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 327
2017 Edition Two-way Wrench Lever with Elliptical Handle 兩用扳柄,橢圓形桿端 |
|
|
|
CNS 4492
2017 Edition Eye Bolts with Small Eyes, M 20 小環首螺栓(M20) |
|
| Find out:6760Items | To Page of: First -Previous-Next -Last | [154] [155] [156] [157] [158] [159] [160] |



