"2,3 " CNS Standards List| Low voltage | Low voltage | Angle Pin | Method Test | Magnesium Alloys | Method Test | Overview digital | Emission safety | |
|
CNS 14104-3
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 12639
2020 Edition Disposable diaper for baby 嬰兒紙尿褲 |
|
|
|
CNS 12035
2020 Edition Writing boards for educational institutions − Ergonomic, technical and safety requirements and their test methods 教育機構用書寫板－人因工程、技術及安全之要求事項與其試驗法 |
|
|
|
CNS 3323
2020 Edition Magnesia-Chrome Brick 鉻鎂磚及鎂鉻磚 |
Translated |
|
|
CNS 2003
2020 Edition Succinic Acid 化學試藥（琥珀酸） |
|
|
|
CNS 15423-3
2020 Edition Equipment for water supply service – Part 3: Test methods of water hammer 自來水用器具－第3部：水鎚試驗法 |
|
|
|
CNS 493
2020 Edition Fine Whitworth Thread (Diameter Ranging From 20 to 189 mm, with Tip Clearance) 韋氏細螺紋（尖端有空隙，直徑自２０至１８９公釐） |
|
|
|
CNS 11523
2020 Edition Method of Test for High - Temperature Fiber Blanket Thermal Insulation 高溫絕熱纖維氈檢驗法 |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 12835-5
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 4: Valves 燃氣用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 13512
2020 Edition Masonry cement 墁砌水泥 |
|
|
|
CNS 6324
2020 Edition Switches of Back-up Lamps for Automobiles 汽車倒車燈開關 |
|
|
|
CNS 3246
2020 Edition Determination of Linean Thermal Expansion of Fired Fine Ceramic and Porcelain Products 已燒製精陶瓷製品線熱膨脹之測定法（膨脹計法） |
|
|
|
CNS 4323
2020 Edition Points for ball point pen refills for school drawing instruments (S) 螺釘端部 |
|
|
|
CNS 15820-3
2020 Edition Electric motorcycles – Safety specifications − Part 3: Specific safety requirements and tests 電動機車－安全規範－第3 部：特定安全要求及試驗 |
|
|
|
CNS 10023
2020 Edition Plutonium By Controlled - Potential Coulometry 布層心體橡膠輸送帶 |
|
|
|
CNS 7032
2020 Edition Dimensions of Link Type Drawbars for Agricultural Wheel Tractors 農業用輪式曳引機連桿型拖桿之尺度 |
|
|
|
CNS 1538
2020 Edition Aluminium Potassium Sulfate 12-Water (Reagent) 化學試藥（１２水合硫酸鉀鋁） |
|
|
|
CNS 14503-2
2020 Edition Evaluation methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Grid method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第２部：柵格法 |
|
|
|
CNS 15423-2
2020 Edition Equipment for water supply service– Part 2: Test methods of low temperature resistant 自來水用器具－第2部：耐寒試驗法 |
|
|
|
CNS 13626
2020 Edition Steel drums - Removable head (open head) 鋼製圓桶－掀蓋式 |
|
|
|
CNS 14123
2020 Edition Metals and alloys − Atmospheric corrosion testing − General requirements for field tests 金屬及合金之腐蝕－大氣腐蝕測試－現場測試之一般要求 |
|
|
|
CNS 60335-2-6
2020 Edition Household and similar electrical appliances − Safety − Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances 家用和類似用途電器－安全性－第2-6部：放置型爐灶、爐架、烤箱及類似電器之個別規定 |
|
|
|
CNS 15423-1
2020 Edition Equipment for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 362
2020 Edition Spokes for Bicycles 自行車（腳踏車）輻絲 |
Translated |
|
|
CNS 13532
2020 Edition Conical Tapers 圓錐錐度 |
|
|
|
CNS 15345-2
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedure 機械安全－降低由機械釋放有害性物質對健康造成之風險－第２部：查證程序之方法 |
|
|
|
CNS 15353-2
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Instrumental method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第２部：儀器測定法 |
|
|
|
CNS 15317-2
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 2: Pipes 冷熱水輸送用交連聚乙烯管－第２部：管 |
|
| Find out:2327Items | To Page of: First -Previous-Next -Last | [11] [12] [13] [14] [15] [16] [17] |
