"an " CNS Standards List |
|
CNS 221
2017 Edition Large Morse Taper Shank Drills 較大（莫氏）推拔柄鑽頭 |
Translated |
|
|
CNS 9103
2017 Edition Symbols of Relays of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電驛類符號 |
|
|
|
CNS 3805
2017 Edition Range Hood 抽油煙機 |
Translated |
|
|
CNS 6153
2017 Edition Method of Test for Electromechanical Switches(Mechanical Endurance) 電機開關檢驗法–機械耐久性 |
|
|
|
CNS 4196
2017 Edition General rules for sampling, sample preparation and analytical testing of non-ferrous metals 非鐵金屬材料之試樣採取、製備及分析檢驗通則 |
|
|
|
CNS 218
2017 Edition Counter-boring Drill with Morse Taper Shank （莫氏）推拔柄柱坑鑽頭 |
Translated |
|
|
CNS 15520
2017 Edition Push and Pull Drain Trap (P Type) 建築物室內用補平塗材 |
|
|
|
CNS 14782
2017 Edition Manipulating industrial robots —Test equipment and metrology methods of operation for robot performance evaluation 工業用機器人性能評估作業之測試儀器與量測方法 |
|
|
|
CNS 5283
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度（齒廓面元線誤差之公差） |
|
|
|
CNS 11570
2017 Edition Remote Control Relays and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 14557
2017 Edition Method of reliability test for road traffic LED display panel 道路用發光二極體文字顯示型交通資訊看板之可靠度測試 |
|
|
|
CNS 15624
2017 Edition Paragliding equipment – Harnesses – Safety requirements and strength tests 飛行傘設備─套袋─安全要求與強度試驗 |
|
|
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器－第11部:助聽器及相關設備之符號及標示 |
|
|
|
CNS 1021
2017 Edition Picks, One Flat End and One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法（使用抗張強度試驗機) |
Translated |
|
|
CNS 3592
2017 Edition Nickel and nickel alloy covered electrodes 鎳及鎳合金被覆銲條 |
|
|
|
CNS 15481-4
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads 道路車輛－電機電子配備環境條件與試驗－第４部：氣候負載 |
|
|
|
CNS 783-2
2017 Edition Sodium carbonate for industrial use - Part 2 : Determination of loss of mass and of non-volatile matter at 250 ℃ 工業用碳酸鈉－第２部：250℃加熱減量及不揮發物測定法 |
|
|
|
CNS 4578
2017 Edition Bolted Connections with Reduced Booy; Metric Thread with Large Clearence, Nominal Values and Limits 減徑柄螺栓之結合法–具大間隙之公制螺紋（標稱尺寸與限界尺寸） |
|
|
|
CNS 7147
2017 Edition Steel Castings for High Temperature and High Pressure Service 高溫高壓用鑄鋼件 |
|
|
|
CNS 6155
2017 Edition Method of Test for Electromechanical Switches(Actuator/Mounting Bushing Resistance) 電機開關檢驗法–主動器、裝架襯套電阻值 |
|
|
|
CNS 6643
2017 Edition Safe working loads,rated-speed and slewing radius of cranes 起重機之額定載重、額定速度與轉動半徑 |
|
|
|
CNS 4250
2017 Edition Square Head Screws with Collar and Half Dog Point with Rounded End Screws 軸環半柱端方頭螺釘 |
|
|
|
CNS 13625
2017 Edition Product analysis and its tolerance for wrought steel 圓形砷化鎵單晶片產品標準 |
|
|
|
CNS 10114
2017 Edition Method for Determining Iron Content in Natural and Artificial Cryolite (1,10-Phenanthroline Photometric Method) 天然及人造冰晶石中鐵定量法（二氮雜菲吸光光度法） |
|
|
|
CNS 2648
2017 Edition Method of Test for Kraft-Paper Tape (Water Soluble, for Polywood Manufacture) 牛皮紙膠帶（水溶性，合板用）檢驗法 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 407
2017 Edition Symbols of Transformers 變壓器符號 |
|
|
|
CNS 9799
2017 Edition Stress and fatigue analyses for pressure vessels 壓力容器之應力解析及疲勞解析 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [158] [159] [160] [161] [162] [163] [164] |
