"p " CNS Standards List |
|
CNS 11794
2018 Edition Minimum Length Between the Cable Entrances and the Terminals of Electric Machinery and Equipment for Marine Use 船用電器電纜導入口與端子間之最小尺度 |
|
|
|
CNS 14162
2018 Edition Information technology - Telecommunications and information exchange between systems - Interface connector and contact assignments for ISDN basic access interface located at reference points S and T 資訊技術–系統間電信與資訊交換–參考點Ｓ和Ｔ之整體服務數位網路基本接取介面的介面連接器及接頭編配 |
|
|
|
CNS 15200-8-5
2018 Edition Methods of test for paints – Part 8-5: Evaluation of degradation of paint coatings – Designation of degree of flaking 塗料一般試驗法－第8-5部： 塗膜劣化評估－片狀剝落 |
|
|
|
CNS 12365
2018 Edition Alphanumeric Character Sets for Optical Recognition - Part II : Character Set OCR-B-Shapes and Dimensions of the Printed Image 光學辨識用文數字集–第二部，ＯＣＲ–Ｂ字集–印出影像之形狀與尺度 |
|
|
|
CNS 9151
2018 Edition 660V, Single-Core, Twin-Core, Three-Core, EpR Insulated PVC Sheathed Metal Netting Covered Cable and 660V, Single-Core, Twin-Core, Three-Core, EPR Insulated PVC Sheathed Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ單心、二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝電纜（附共同遮蔽）及６６０Ｖ單心、二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附共同遮蔽） |
|
|
|
CNS 4394-5
2018 Edition plastics − Injection moulding of test specimens of thermoplastic materials − Part 4: Determination of moulding shrinkage 塑膠－熱塑性塑膠射出成型試片－第5部：研究異向性標準試片之製備 |
|
|
|
CNS 5341
2018 Edition Determination of density for vulcanized or thermoplastic rubber 硫化橡膠或熱塑性橡膠密度測定法 |
|
|
|
CNS 14160
2018 Edition Information technology - Telecommunications and information exchange between systems - Start stop transmission signal quality at DTE/DCE interfaces 資訊技術–系統間電信與資訊交換–數據終端設備與數據電路終接設備間介面的起停傳輸信號品質 |
|
|
|
CNS 12451
2018 Edition Methods for Measuring Specific Gravity of Solid 固體比重測定法 |
|
|
|
CNS 14620
2018 Edition Roller sports equipment − Inline-skates 輪式運動器材－直排輪鞋 |
|
|
|
CNS 4024
2018 Edition permissible Deviations in Dimensions Without Tolerance Indication (Steel Castings) 一般許可差（鋼鑄件） |
|
|
|
CNS 15568
2018 Edition protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 14213-1
2018 Edition Information technology - Open systems interconnection - Procedures for the operation of OSI registration authorities - Part 1:General procedures 資訊技術–開放系統互連–開放系統互連註冊機構作業程序–第１部：一般程序 |
|
|
|
CNS 15200-7-5
2018 Edition Methods of test for paints − Part 7-5: Long-period performance of film − Natural weathering 塗料一般試驗法－第7-5部：塗膜之長期性能－室外暴露耐候性 |
|
|
|
CNS 3327
2018 Edition Method of Test for pin Adhesion of Corrugated Board by Selective Separation 瓦楞紙板膠合強度試驗法 |
|
|
|
CNS 15620-2-1
2018 Edition Insulation coordination for equipment within low-voltage system – Part 2-1: Application Guide – Dimensioning procedure worksheets and dimensioning examples 低電壓系統下設備之絕緣協調－第2-1 部： 應用指引－ 尺寸量測程序工作表及尺寸量測範例 |
|
|
|
CNS 13660-2
2018 Edition File Transfer,Access and Management (FTAM)-part 2:Definition of Type,Constraint Sets and Syntaxes 檔案轉送、存取及管理–第２部分：文件型式限制集合與語法基本定義 |
|
|
|
CNS 1354
2018 Edition Methed of test for tensile properties of paper and board (Pendulum mehod) 紙及紙板抗張性質試驗法（擺錘法） |
|
|
|
CNS 10134
2018 Edition Method of Test for Delivered Mass of Aerosol products 噴霧性產品噴出量試驗法 |
|
|
|
CNS 15037-2
2018 Edition Walking aids manipulated by both arms - Requirements and test methods - Part 2: Rollators 雙臂操作步行輔具－要求及測試法－第２部：帶輪助行器 |
|
|
|
CNS 14912
2018 Edition Fundamental aspects of safety standards for medical electrical equipment 醫電設備之安全標準規範 |
|
|
|
CNS 14431
2018 Edition Method of test for performance of oil/grease interceptor 油脂截留器性能試驗法 |
|
|
|
CNS 15609-3
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings 熱塑性塑膠管與管件－衛氏軟化溫度－第3部：丙烯腈-丁二烯-苯乙烯及丙烯腈-苯乙烯-丙烯酸酯管與管件之試驗條件 |
|
|
|
CNS 15620-3
2018 Edition Insulation coordination for equipment within low-voltage system – Part 3: Use of coating, potting or moulding for protection against pollution 低電壓系統下設備之絕緣協調－第3 部：用於污染防護之塗裝、封裝或壓塑 |
|
|
|
CNS 8751
2018 Edition polyolefin pipes for the conveyance of fluids − Determination of resistance to crack propagation − Test method for slow crack growth on notched pipes 聚烯羥類織袋用帶狀延伸紗 |
|
|
|
CNS 13741-3
2018 Edition Information technology-Open systems interconnection-Virtual terminal basic class-application profiles-Part 3:AVT 22-S-mode forms application profile 資訊技術–開放系統互連–虛擬終端機基本類別–應用規範–第３部：同步模式表格應用規範 |
|
|
|
CNS 13911
2018 Edition Information technology - Open systems interconnection - Virtual terminal basic class service 資訊技術–開放系統互連–虛擬終端機基本類別服務 |
|
|
|
CNS 16050
2018 Edition Welding consumables − Gases and gas mixtures for fusion welding and allied processes 銲接材料－熔融銲接及相關程序用氣體及混合氣 |
|
|
|
CNS 15620-5
2018 Edition Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining clearance and creepage distances equal to or less than 2 mm 低電壓系統下設備之絕緣協調－第5 部： 決定2 mm 以下空間距離及沿面距離之詳盡方法 |
|
|
|
CNS 27009
2018 Edition Information technology − Security techniques − Sector-specific application of CNS 27001 − Requirements 資訊技術－安全技術－CNS 27001之產業特定應用－要求事項 |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [158] [159] [160] [161] [162] [163] [164] |
