"b, " CNS Standards List |
|
CNS 5507
2017 Edition Rolling Bearings; Bearing with Spherical Outside Surface and Extended Inner Ring Width, Insert bearings 嵌入夾緊滾動軸承（具球面外環與加寬內環） |
|
|
|
CNS 12289
2017 Edition Reliability Assured Fixed Metal Film Resistors (H,J,K) (Established Failure Rate) 可靠度保證金屬皮膜固定電阻器（特性Ｈ，Ｊ及Ｋ）（故障率設定） |
Translated |
|
|
CNS 9367
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 14 Ozone Exposure) 頻率３ＭＨｚ以下電連接器檢驗法（耐臭氧試驗ＴＰ–１４） |
|
|
|
CNS 4366
2017 Edition Hexagon Bolts with Large Widths Across Flats for Steel Structures (Joints with Hightensile, Prestressed Bolts) 六角頭螺栓（具大對面寬度、高預力連接鋼結構用） |
|
|
|
CNS 3500
2017 Edition Method of Test for Surface Strength of Paper and Paper Board ( Wax Pick Test) 紙及紙板表面強度蠟棒檢驗法 |
Translated |
|
|
CNS 8937
2017 Edition Method of Test for Travelling Cables for Elevators 升降機用移動電纜檢驗法 |
|
|
|
CNS 4849
2017 Edition Core Plugs, Core Plug Bars 心塞、心塞桿 |
|
|
|
CNS 14800
2017 Edition Method of test for resistance of materials used in protective clothing to penetration by blood-borne pathogens using Phi-X174 bacteriophage penetration as a test system 使用Phi-X174噬菌體穿透力之試驗系統供防護衣材料對血液媒介病原穿透阻力的試驗法 |
|
|
|
CNS 8188
2017 Edition Method of Test for Water Retention by Concrete Curing Materials 混凝土養護材料保持水份能力檢驗法 |
|
|
|
CNS 14673
2017 Edition Interference to mobile radiocommunications in the presence of impulsive noise - Methods of judging degradation and measures to improve performance 脈衝性雜訊對行動無線通信的干擾－產品劣化的判定方式及其性能的改善方法 |
|
|
|
CNS 15996
2017 Edition Plastic fuel tanks for passenger cars (replaced by CNS 14579-1) 燃氣用塑膠軟管 |
|
|
|
CNS 9114
2017 Edition Symbols of Television and Broadcast Equipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 100
2017 Edition Accuracy Inspection of Table Type Horizontal Boring Machines 床台型臥式搪床精度檢驗 |
Translated |
|
|
CNS 10001
2017 Edition Seamless Nickel-Chromium-Iron Alloy Tubes for Heat Exchanger 熱交換器用無縫鎳鉻鐵合金管 |
|
|
|
CNS 2089
2017 Edition Edible Melon Seed 食用瓜子 |
Translated |
|
|
CNS 15628-1
2017 Edition Wheelchair seating - Part 1: Vocabulary, reference axis convention and measures for body segments, posture and postural support surfaces 輪椅乘坐系統－第1部：詞彙、參考軸協定及身體肢段、姿勢與姿勢支撐面之量測 |
|
|
|
CNS 4738
2017 Edition General Rules of Connectors for Radio Frequency Coaxial Cables 射頻同軸連接器總則 |
|
|
|
CNS 14182
2017 Edition Reliability and lot control tests for analog video laser transmitter and receiver modules used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 15552
2017 Edition Packaging - Accessible design - General requirements 包裝－無障礙設計 - 一般要求 |
|
|
|
CNS 11707
2017 Edition Method of Test for Fiber Optic Devices (FOTP-51 Pulse Distortion Measurement of Multimode Glass Optical Fiber Information Transmission Capacity) 光纖組件檢驗法（多模式玻璃光纖資訊傳輸容量之脈波失真測量ＦＯＴＰ–５１） |
|
|
|
CNS 11705
2017 Edition Method of Test for Fiber Devices (FOTP-20 Change of Optical Transmittance) 光纖組件檢驗法（透射率改變ＦＯＴＰ–２０） |
|
|
|
CNS 6002
2017 Edition Tooth Belts for Sewing Machines 縫紉機齒形皮帶 |
|
|
|
CNS 9112
2017 Edition Symbols of Telephone and Bell of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電話、電鈴類符號 |
|
|
|
CNS 13375
2017 Edition Gauge Blanks for Screw Thread Limit Gauges 螺紋限界量規之形狀及尺度 |
|
|
|
CNS 8902
2017 Edition Method of Test for Oil Based Caulking Compounds for Building 建築用油性填縫材料檢驗法 |
|
|
|
CNS 15558-1
2017 Edition Flexible cellular polymeric materials - Physical properties - Part 1: General rules 軟質發泡材料－物理特性－第１部：通則 |
|
|
|
CNS 5672
2017 Edition Arbor End Collars for Milling Machines 銑刀心軸端軸環 |
|
|
|
CNS 9621
2017 Edition Rubber hoses for liquefied petroleum gases (LPGs) − Automobile, general equipment and home application 液化石油氣用橡膠管(LPG 橡膠管)－汽車、一般設備及家庭用 |
|
|
|
CNS 12295
2017 Edition General Rules for Reliability Assured Power Type Fixed Wire Wound Resistors 可靠度保證功率型線繞固定電阻器總則 |
|
|
|
CNS 9110
2017 Edition Symbols of Bus - Bar of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖滙流排槽類符號 |
|
| Find out:7153Items | To Page of: First -Previous-Next -Last | [160] [161] [162] [163] [164] [165] [166] |
