"AT " CNS Standards List |
|
CNS 8474
2017 Edition Punched Tape Variable Block FormAT for Positioning and Straight - Cut Numerically Controlled Machine Tools 衝頭（對孔用） |
|
|
|
CNS 14368
2017 Edition Micrographics-RecommendATions for the creation of original documents 微縮技術－製作原始文件的建議 |
|
|
|
CNS 2305
2017 Edition Asphalt LaminATing Paper 夾層柏油紙 |
Translated |
|
|
CNS 15495
2017 Edition Test methods of tensile adhesive strength for thermal-sprayed coATings 熔射塗層拉伸附著強度試驗法 |
|
|
|
CNS 4774
2017 Edition Electric HotplATes 家用電爐 |
Translated |
|
|
CNS 6150
2017 Edition Method of Test for Electromechanical Switches(Terminal TemperATure Rise) 電機開關檢驗法–端子溫度上昇 |
|
|
|
CNS 5376-4
2017 Edition Iron ores—Method for determinATion of combined water content 鐵礦石—結合水定量法 |
|
|
|
CNS 12672
2017 Edition Method of Test for Radiographic and ClassificATion of Radiographs of Aluminum 鋁熔接縫放射線透射試驗法及透射照片之等級分類 |
|
|
|
CNS 14890
2017 Edition RegenerATed fiber cement boards 再生纖維水泥板 |
|
|
|
CNS 4322
2017 Edition Hexagon Bolts with Thread ApproximATely to Head, Regular, Metric Thread 六角頭全螺紋螺栓（粗製） |
|
|
|
CNS 7149
2017 Edition Steel Castings for Low TemperATure and High Pressure Service 低溫高壓用鑄鋼件 |
|
|
|
CNS 6661
2017 Edition Colors for Color IdentificATion and Coding 色碼用之標準顏色 |
|
|
|
CNS 1021
2017 Edition Picks, One FlAT End and One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm CoordinATion of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 783-2
2017 Edition Sodium carbonATe for industrial use - Part 2 : Determination of loss of mass and of non-volatile matter at 250 ℃ 工業用碳酸鈉－第２部：250℃加熱減量及不揮發物測定法 |
|
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerATions and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
|
|
|
CNS 14604
2017 Edition ManipulATing industrial robots -Automatic end effector exchange system-vocabulary and presentation of characteristics 工業用機器人－端效器自動交換系統－詞彙及特性 |
|
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for IndicATion) 發光二極體(指示用) |
|
|
|
CNS 13331
2017 Edition Sound CalibrATor 音壓校正器 |
|
|
|
CNS 13347
2017 Edition Method of Test for Acrylonitrile - Butadiene - Styrene (ABS) Plastic Fittings for WATer Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管接頭配件檢驗法 |
|
|
|
CNS 6155
2017 Edition Method of Test for Electromechanical Switches(ActuATor/Mounting Bushing Resistance) 電機開關檢驗法–主動器、裝架襯套電阻值 |
|
|
|
CNS 15481-4
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: ClimATic loads 道路車輛－電機電子配備環境條件與試驗－第４部：氣候負載 |
|
|
|
CNS 7178
2017 Edition Protective gloves for occupATional health 熔接用防護手套 |
|
|
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and relATed equipment 助聽器－第11部:助聽器及相關設備之符號及標示 |
|
|
|
CNS 14382
2017 Edition Protective gloces against chemicals and micro-organisms - Part 3:DeterminATion of resistance to permeation by chemicals 防護手套－一般要求及試驗方法 |
|
|
|
CNS 13127
2017 Edition Metallic and Other Non -organic CoATings -General Rules for Stationary Outdoor Exposure Corrosion Tests 金屬和無機被覆–靜態戶外曝露腐蝕試驗通則 |
|
|
|
CNS 12775
2017 Edition Low energy air guns for recreATion 低動能遊戲用槍 |
Translated |
|
|
CNS 4070
2017 Edition High Speed PneumATic Grinders 高速氣動輪磨機 |
Translated |
|
|
CNS 15091-1
2017 Edition Method of test for deep sea wATer - Measurement of in-situ temperature 深層海水檢驗法－現場溫度之測量 |
|
|
|
CNS 4363
2017 Edition Slotted Countersunk (FlAT) Head Screws for Fine Mechanics M 0.4 to M 1.4 精密用有槽平頂埋頭螺釘（標稱直徑自0.4mm至1.4mm） |
|
| Find out:7080Items | To Page of: First -Previous-Next -Last | [162] [163] [164] [165] [166] [167] [168] |
