"an " CNS Standards List |
|
CNS 14384-1
2017 Edition Protective gloves − General requirements and test methods 化學藥品及微生物防護手套－用語及性能要求 |
|
|
|
CNS 15520
2017 Edition Push and Pull Drain Trap (P Type) 建築物室內用補平塗材 |
|
|
|
CNS 12082
2017 Edition Method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量ＦＯＴＰ–３０） |
|
|
|
CNS 15625-2
2017 Edition Paragliding equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics 飛行傘設備─飛行傘─第2部：飛行安全性分類要求與試驗法 |
|
|
|
CNS 12926
2017 Edition 100mm.65mm Stationary Handling Operated Fire Water Monitor １００ｍｍ、６５ｍｍ進出水口固定型操作式消防水瞄 |
|
|
|
CNS 14694-2
2017 Edition Audio , video and audiovisual systems-interconnections and matching values Part 2：21-pin connector for video systems-application No.2 聲音、影像及視聽系統之互連與匹配值－第２部：影像系統適用之２１針連接器－第２類應用 |
|
|
|
CNS 4241
2017 Edition Method of Test for Electroplated Coating of Bolts, Screws and Nuts 螺栓、螺釘、螺帽電鍍層之檢驗法 |
|
|
|
CNS 6641
2017 Edition Rope sheaves for overhead travelling cranes 架空移動起重機用鋼纜槽輪 |
|
|
|
CNS 6414
2017 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條（一般機械及重機械用） |
|
|
|
CNS 1065
2017 Edition Candles 蠟燭 |
|
|
|
CNS 12937
2017 Edition Structure of Welded SteelTanks for Petroleum Oil Storage 鋼製全熔接石油類儲槽構造 |
|
|
|
CNS 2692
2017 Edition Pliers and nippers - Pliers for gripping and manipulating 夾鉗與剪鉗－滑節轉樞夾鉗（鯉魚鉗） |
|
|
|
CNS 3440
2017 Edition Method of test for milk and milk products - General rules 乳品檢驗法－總則 |
Translated |
|
|
CNS 12509
2017 Edition General Rules analytical Methods in Gas Chromatography/Mass Spectrometry 氣相層析／質譜分析法通則 |
|
|
|
CNS 12886-1
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法─120℃或150℃乾熱處理 |
Translated |
|
|
CNS 13006
2017 Edition MAG Welding Solid Wire for Molybdenum Steel and Chromium Molybdenum Steel 鉬鋼及鉻鉬鋼ＭＡＧ熔接用實心鋼線 |
|
|
|
CNS 3198
2017 Edition Silicon Sand (for Castings) 矽砂（鑄造用） |
|
|
|
CNS 15210-6
2017 Edition Information technology - Radio frequency identification for item management - Part 6: Parameters for air interface communications at 860MHz to 960MHz 資訊技術─品項管理之無線射頻識別─第６部：８６０ＭＨｚ至９６０ＭＨｚ空中介面通信參數 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 14623-2
2017 Edition Sterilization of health care products-chemical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 146
2017 Edition Height of Shaft, for Driving and Driven Lines 軸心高度，主動機及從動機 |
|
|
|
CNS 13982-7
2017 Edition Methods of test for bulk down and feather − Part 7: Determination of oxygen number 羽絨羽毛試驗法－第7部：耗氧指數測定法 |
|
|
|
CNS 6677
2017 Edition Essential oils － Determination of ester values, before and after acetylation, and evaluation of the contents of free and total alcohols 精油－自由與總醇含量估計法（酯值測定法） |
|
|
|
CNS 10000
2017 Edition Wire Ropes for Mechanical Control 機械控制用鋼纜 |
|
|
|
CNS 12844
2017 Edition Method of Test for Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布檢驗法 |
Translated |
|
|
CNS 4172
2017 Edition Short Pitch Transmission Precision Bush Chains and Chain Wheels 短節距傳動用精確襯套鏈條及鏈輪 |
|
|
|
CNS 10151
2017 Edition Method of Test for Performance of Jig Boring Machines 工模搪床之動態檢驗法 |
|
|
|
CNS 13011
2017 Edition Filler rods and solid wires for TIG welding of 9% nickel steel ９﹪鎳鋼用ＴＩＧ銲接裸銲條及實心銲線 |
|
|
|
CNS 13982-4
2017 Edition Methods of test for bulk down and feather − Part 4: Determination of the oil and fat content 羽絨羽毛試驗法－第4部：油脂含量測定法 |
|
|
|
CNS 14466-10
2017 Edition Audiovisual,video and television equipment and systems. Part10:Audio cassette system 視聽．影像及電視設備與系統-第１０部：音訊卡帶系統 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [162] [163] [164] [165] [166] [167] [168] |
