"With " CNS Standards List |
|
CNS 4856
1998 Edition Fixed capacitors for use in electronic equipment (Aluminium electrolytic capacitors With solid and non-solid electrolyte) 電子設備用鋁質電解電容器（固體及非固體電解質） |
|
|
|
CNS 14267
1998 Edition Wood ploes treated With creosote oil 注雜酚油防腐木桿 |
|
|
|
CNS 541
1997 Edition Shovels With Point End 尖鏟 |
Translated |
|
|
CNS 13991
1997 Edition Fixed resistor networks With individually measurable resistors for use in electronic equipment 電子設備用可單獨量測個別電阻元件之固定網路電阻器 |
|
|
|
CNS 2862
1994 Edition Deep Groove Ball Bearings: Single - Row Without Filling Notch 徑向深溝滾珠軸承（單列、無填裝槽） |
Translated |
|
|
CNS 4434
1993 Edition Round Nuts With Drilled Holes in One Face 頂孔圓螺帽 |
|
|
|
CNS 4433
1993 Edition Round Nuts With Set Pin Hole in Side 側孔圓螺帽 |
|
|
|
CNS 13217
1993 Edition Cold Rolled High Strength Steel Sheets With Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 853
1993 Edition Cross Joints With Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
|
|
CNS 1488
1993 Edition Knife Switches (With Cover) 有蓋閘刀開關 |
Translated |
|
|
CNS 13216
1993 Edition Hot - rolled High Strength Steel Sheets With Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 2251
1992 Edition Aluminium Foil Laminated With Paper Lining 褙紙鋁箔 |
|
|
|
CNS 13059-3
1992 Edition Photovoltaic Devices Part 3：Measurement Principles for Terrestrial Photovoltaic (PV) Solar Devices With Reference Spectral Irradiance Data 光電伏打元件（第三部：具光譜照射光參考數據之陸上光電伏打(PV)太陽元件量測原理） |
|
|
|
CNS 219
1991 Edition Counter-boring Drill With Straight Shank 直柄柱坑鑽頭 |
Translated |
|
|
CNS 12882
1991 Edition Method of Test for Hook Drawing Resistance of Cement Sack Paper Laminated With Plastic Woven Sheet 塑膠編織貼合水泥袋紙鈎裂強度試驗法 |
Translated |
|
|
CNS 12880
1991 Edition Cement Sack Paper Laminated With Plastic Woven Sheet 塑膠編織貼合水泥袋紙 |
Translated |
|
|
CNS 218
1991 Edition Counter-boring Drill With Morse Taper Shank （莫氏）推拔柄柱坑鑽頭 |
Translated |
|
|
CNS 215
1990 Edition Long Drills With Straight Shank and Tenon Drive 驅動榫直柄長鑽頭 |
Translated |
|
|
CNS 214
1990 Edition Long Drills With Straight Shank 直柄長鑽頭 |
Translated |
|
|
CNS 210
1990 Edition Short Drills With Square Taper Shank 方錐柄短鑽頭 |
Translated |
|
|
CNS 12711
1990 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use With Printed Boards 使用印刷電路板用頻率3 MHz以下連接器之微處理機系統之接腳配置 |
|
|
|
CNS 12727
1990 Edition Method of Test for Control Cables With Shields 遮蔽型控制電纜檢驗法 |
|
|
|
CNS 209
1990 Edition Long Drills With Square Taper Shank 方錐柄長鑽頭 |
Translated |
|
|
CNS 213
1990 Edition Stub Drills With Straight Shank and Tenon Drive 驅動榫直柄短鑽頭 |
Translated |
|
|
CNS 3607
1988 Edition Single Angle Milling Cutters With Threaded Holes 附螺紋孔單側角銑刀 |
Translated |
|
|
CNS 4366
1987 Edition Hexagon Bolts With Large Widths Across Flats for Steel Structures (Joints with Hightensile, Prestressed Bolts) 六角頭螺栓（具大對面寬度、高預力連接鋼結構用） |
|
|
|
CNS 11877
1987 Edition Phonograph Pick-Ups With 12.7mm Mounting 12.7 mm安裝孔距之電唱機拾音器 |
|
|
|
CNS 4321
1987 Edition Hexagon Bolts With Approximately to Head, Finished and Semi-Finished, Metric Fine Thread 六角頭全螺紋螺栓（精製及半精製，公制細螺紋） |
|
|
|
CNS 3120
1987 Edition Hexagon Bolts With Small Widths Across Flats 六角頭螺栓（具小對面寬度） |
|
|
|
CNS 11999
1987 Edition Structural Steels With Specified Hardenability Bands 保證硬化能構造用鋼料（Ｈ鋼） |
|
| Find out:672Items | To Page of: First -Previous-Next -Last | [12] [13] [14] [15] [16] [17] [18] |
