"CNS " CNS Standards List| Method Test | Safety machinery | Liquid petroleum | Information technology | Acoustics | Deep groove | Quality management | Space systems | |
|
CNS 15711-2
2019 Edition Photovoltaic (PV) module performance testing and energy rating − Part 2: Spectral responsivity, incidence angle and module operating temperature measurements 太陽光電模組性能試驗及能量定額－第2部：光譜響應度、入射角及模組操作溫度量測 |
|
|
|
CNS 15033
2019 Edition Solar energy - Specification and classification of instruments for measuring hemispherical solar and direct solar radiation 太陽能－量測半球太陽輻射與直接太陽輻射儀器之規格及分級 |
|
|
|
CNS 14935
2019 Edition Measurement of amplifier power gain and noise figure 放大器功率增益與雜訊指數之量測法 |
|
|
|
CNS 11067
2019 Edition Carbon and Alloy Steel Forgings for Pressure Vessels for Low Temperature Service 低溫壓力容器用碳鋼及合金鋼鍛鋼件 |
|
|
|
CNS 14904
2019 Edition Essential oils - General guidance on the determination of flashpoint 精油－閃點測定法 |
|
|
|
CNS 8700
2019 Edition Quenched and Tempered Alloy Steel Forgings for Pressure Vessels 壓力容器用淬火–回火合金鋼鍛鋼件 |
|
|
|
CNS 2424
2019 Edition Brown rice 糙米 |
Translated |
|
|
CNS 15190
2019 Edition Appraisal requirements for CMMI 能力成熟度模型整合之評鑑要求 |
|
|
|
CNS 695
2019 Edition Small Switches for Indoor Use 室內用小型開關 |
Translated |
|
|
CNS 15785-2
2019 Edition Tool holders with cylindrical shank − Part 2: Type A, shanks for tool holders of special designs 具圓柱柄之刀具夾持器－第2 部：特殊設計之A 型 |
|
|
|
CNS 15785-1
2019 Edition Tool holders with cylindrical shank − Part 1: Cylindrical shank, location bore − Technical delivery conditions 具圓柱柄之刀具夾持器－第1 部：圓柱柄及定位孔－交貨之技術條件 |
|
|
|
CNS 13181-7
2019 Edition The Method of Test of Leakages Testing Procedures for LGP Automobile Fuel Systems 液化石油氣汽車燃氣系統–洩漏測試程序 |
Translated |
|
|
CNS 12493
2019 Edition High Density Polyethylene Geomembrane for Sanitary Landfill 垃圾掩埋場用高密度聚乙烯不透水布 |
Translated |
|
|
CNS 8566
2019 Edition Method of Test for Air Brakes of Automobiles 汽車用氣煞車試驗法 |
|
|
|
CNS 4527
2019 Edition Method of test for calcium phosphates(for feed) 飼料用磷酸鈣類檢驗法 |
|
|
|
CNS 13519
2019 Edition Zinc alloys used as galvanic anodes for cathodic protection 陰極保護用鋅合金犧牲陽極 |
|
|
|
CNS 7506
2019 Edition Method of Test for Ramie Canvas 苧麻帆布檢驗法 |
|
|
|
CNS 15008
2019 Edition Systems engineering - System life cycle processes 系統工程－系統生命週期過程 |
|
|
|
CNS 1449
2019 Edition Watermelon 西瓜 |
Translated |
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 15097
2019 Edition IPv6 over PPP 經由ＰＰＰ之ＩＰｖ６協定 |
|
|
|
CNS 15706
2019 Edition Method of test for shell content in fine aggregates 細粒料中貝殼含量測定法 |
|
|
|
CNS 9846
2019 Edition Light Extinction Type Smokemeters for Diesel Automobiles 柴油車用透光式排氣煙度計 |
|
|
|
CNS 15136
2019 Edition Learning Object Metadata (LOM) 學習物件詮釋資料 |
|
|
|
CNS 6
2019 Edition Electrolytic Cathode Copper 電解銅 |
Translated |
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inverted vertical workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 15239
2019 Edition Method of test for bursting strength of paper and board after immersion in water 紙及紙板浸水破裂強度試驗法 |
|
|
|
CNS 13059-5
2019 Edition Photovoltaic devices − Part 5: Determination of the equivalent cell temperature (ECT) of photovoltaic (PV) devices by the open-circuit voltage method 太陽光電裝置－第5 部：以開路電壓法測定太陽光電裝置之等效電池溫度 |
|
|
|
CNS 2709
2019 Edition Method of Test for Cotton Canvas 棉帆布檢驗法 |
Translated |
|
|
CNS 11531
2019 Edition Method of Test for Stability of Reach Fork Lift Trucks and Straddle Fork Lift Trucks 伸縮型及跨提型叉舉車安定性檢驗法 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [168] [169] [170] [171] [172] [173] [174] |
