"C,E " CNS Standards List |
|
CNS 246
2019 Edition Machine-Reamers with Parallel Shanks 機用鉸刀（圓柱柄） |
|
|
|
CNS 15141
2019 Edition Textiles - Determination of fabric propensity to surface fuzzing and to pilling : Pilling box method 紡織品起毬檢驗法－盒型起毬試驗法 |
|
|
|
CNS 13984
2019 Edition Methods of test for thermal diffusivity,specific heat capacity,and thermal conductivity of fine ceramics by laser flash method 精密陶瓷依雷射閃光法之熱擴散率、比熱容量、熱傳導率試驗法 |
|
|
|
CNS 5436
2019 Edition Method of Performance Test for Insulated Bodies of Insulated or Refrigerated Vehicles 冷藏、冷凍汽車之保冷車體性能試驗法 |
|
|
|
CNS 16094-2
2019 Edition Ductile iron pipes, fittings, accessories and their joints − External zinc-based coating − Part 2: Zinc-rich paint 延性鑄鐵管、管件、配件及接頭－外部鋅基塗層－第2部：富鋅塗料 |
|
|
|
CNS 15743
2019 Edition Guidelines for older persons and persons with disabilities − Information presentation using electronic guiding and wayfinding system 年長者與身心障礙者之指導綱要－使用電子導引及支援移動系統之資訊呈現 |
|
|
|
CNS 14944
2019 Edition Essential oils – General guidance on chromatographic profiles – Part 2: Utilization of chromatographic profiles of samples of essential oils 精油－層析特性成分分布通則－第2部：精油樣品層析特性成分分布之應用 |
|
|
|
CNS 5618
2019 Edition Method of Test for Nonwoven Fabrics Defects 非織物瑕疵檢驗法 |
|
|
|
CNS 2680
2019 Edition Nitrogen Gas, Compressed in Cylinder 高壓瓶裝氮氣 |
|
|
|
CNS 15462
2019 Edition Method of test for flow consistency of controlled low strength material (CLSM) 控制性低強度材料流動稠度試驗法 |
|
|
|
CNS 15076-1
2019 Edition Modular units for machine tools - Workholding pallets - Part 1 : Workholding pallets up to 800 mm nominal size 工具機之模組單元－工件固定托板－第１部：標稱尺度８００ｍｍ以下之工件固定托板 |
|
|
|
CNS 16099
2019 Edition Standard test method for pull-off adhesion strength of coatings on concrete using portable pull-off adhesion testers 可攜式拉脫試驗儀於混凝土塗層之拉脫黏著強度試驗法 |
|
|
|
CNS 3489
2019 Edition Polyacrylonitrile Spun Yarns, Cotton System, Unfinished Regular Yarn 聚丙烯腈棉狀纖維（非收縮型） |
Translated |
|
|
CNS 14901
2019 Edition Essential oils - General rules for labelling and marking of containers 精油－容器標籤與標示通則 |
|
|
|
CNS 5346-2
2019 Edition Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials 塑膠－縮寫用語與符號（第３部：可塑劑） |
|
|
|
CNS 13500
2019 Edition Method of Test for Grains - Moisture Contents of Cereals 穀類檢驗法–禾穀水分 |
Translated |
|
|
CNS 15785-1
2019 Edition Tool holders with cylindrical shank − Part 1: Cylindrical shank, location bore − Technical delivery conditions 具圓柱柄之刀具夾持器－第1 部：圓柱柄及定位孔－交貨之技術條件 |
|
|
|
CNS 15601
2019 Edition Commercial vehicles − Obstacle detection device during reversing − Requirements and tests 商用車－倒車障礙物偵測裝置－要求與試驗 |
|
|
|
CNS 11795
2019 Edition Hard Lead Plates 硬鉛板 |
|
|
|
CNS 15200-3-3
2019 Edition Method of test for coatings − Part 3-3: Film formability of coatings − Through-dry 塗料一般試驗法－第3-3部：塗膜成形性－堅結乾燥性 |
|
|
|
CNS 9382
2019 Edition Method of Test for Multi - Connectors for Automotives 汽車用多根接頭試驗法 |
|
|
|
CNS 8680
2019 Edition Method of Braking Device Dynamometer Test for Trucks and Buss 貨車、大客車煞車裝置─測功計試驗法 |
|
|
|
CNS 15175
2019 Edition High-voltage test techniques - Partial discharge measurements 高電壓試驗技術－部分放電量測 |
|
|
|
CNS 10660
2019 Edition Method of Test for Polyethylene Films for Agriculture 農業用聚乙烯塑膠膜檢驗法 |
|
|
|
CNS 15167
2019 Edition Showerhead 蓮蓬頭 |
|
|
|
CNS 16097-1
2019 Edition Machine tools − Dimensions and geometric tests for self-centring chucks with two-piece jaws − Part 1: Manually operated chucks with tongue and groove type jaws 工具機－具兩件式夾爪之自定心夾頭的尺度及幾何試驗－第1部：具榫槽式夾爪之手動操作夾頭 |
|
|
|
CNS 14874
2019 Edition Edible mid-oleic acid sunflowerseed oil 食用中量油酸葵花籽油 |
|
|
|
CNS 15755-5-9
2019 Edition Conversion tables for units − Part 5-9: Pressure or stress − Megapascal and standard atmosphere 單位換算表－第5-9 部：壓力或應力－百萬帕斯卡與標準大氣壓 |
|
|
|
CNS 1168
2019 Edition Method of Test for Resistance of Concrete Specimens to Rapid Freezing and Thawing in Water 混凝土試體抵抗凍融試驗法（水中快速凍融法） |
|
|
|
CNS 6514
2019 Edition General Rules of Acid Resisting Porcelain for Chemical Industry 化學工業用耐酸陶瓷器總則 |
|
| Find out:15848Items | To Page of: First -Previous-Next -Last | [169] [170] [171] [172] [173] [174] [175] |
