"0 " CNS Standards List |
|
CNS 12106
1987 Edition Method of Test for Water Absorbency of Bibulous Paper -- Absorption Rate Method 高吸水性紙吸水性試驗法－吸水速率法 |
Translated |
|
|
CNS 11875
1987 Edition Fixed Mica Capacitors (Type CM 50) 雲母固定電容器(CM50型) |
|
|
|
CNS 9234
1987 Edition Method of Test for Dry Reed Switches (Standard Test Coils, Single Insulation 130 ℃ Wire) 乾式簧開關檢驗法（130℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 6097
1987 Edition Underfloor Ducts(Steel) 鋼製地板電線槽 |
|
|
|
CNS 2063
1987 Edition Outdoor Nylon Sheathed Telephone Wires for Communication Lines 尼龍被覆電話線（架設通信線路用） |
Translated |
|
|
CNS 11940
1987 Edition Standard Parts of Injection Mold 塑膠型模形狀及其標準組件 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 4079
1987 Edition Wire Spring Relay 線簧電驛 |
|
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 12068
1987 Edition Support of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 6071
1987 Edition 600 V Silicon Rubber Insulated Glass Fiber Braided Wires 600 V矽橡膠絕緣玻璃纖維編織電線 |
Translated |
|
|
CNS 5770
1987 Edition General Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting Molds 壓鑄模用頂出桿 |
|
|
|
CNS 12007
1987 Edition Method of Test for Helical Scanning Video Tape Recorders 螺線掃描錄放影機檢驗法 |
|
|
|
CNS 12074
1987 Edition Flash Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 3070
1987 Edition Insulating Oil (for Cold Area) 絕緣油（寒地用） |
Translated |
|
|
CNS 4700
1987 Edition Hexagon Head Bolts with Thread Approximately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓（具小對面寬度） |
|
|
|
CNS 9097
1987 Edition Thermostats ( Pressure Type ) 恆溫器（壓力式） |
|
|
|
CNS 3120
1987 Edition Hexagon Bolts with Small Widths Across Flats 六角頭螺栓（具小對面寬度） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 12075
1987 Edition Wall Thickness and Height for Different Cross Sections of Hot Forging Closed Die 熱鍛閉合模之不同形狀斷面最小厚度及最小高度 |
|
|
|
CNS 12073
1987 Edition Die Materials of Hot Forging Closed Die 熱鍛閉合模之模具材料 |
|
|
|
CNS 12170
1987 Edition Method of Test for Fiber Optic Devices (FOTP-16 Salt Spray Corrosion Test) 光纖裝置檢驗法（鹽水噴霧腐蝕試驗FOTP-16） |
|
|
|
CNS 11900
1987 Edition Fixed Ceramic Capacitors for Electronic Equipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 12108
1987 Edition Method of Test for Acid-Soluble Lignin in Wood and Pulp 木材及紙漿中酸溶性木質素試驗法 |
Translated |
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 11608
1986 Edition Unplasticized Polyvinyl Chloride Pipes with Fiberglass Reinforced Plastic Reinforcement 玻璃纖維強化塑膠加強聚氯乙烯塑膠硬質管 |
Translated |
|
|
CNS 7660
1986 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 21 Insulation Resistance) 頻率3 MHz以下電連接器檢驗法（絕緣電阻T-21） |
|
|
|
CNS 8220
1986 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 31 Humidity Test ) 頻率3 MHz以下電連接器檢驗法（耐濕性試驗TP-31） |
|
| Find out:5722Items | To Page of: First -Previous-Next -Last | [172] [173] [174] [175] [176] [177] [178] |
