"V " CNS Standards List |
|
CNS 9814
2021 Edition Low-Voltage single-phase induction motors for construction submersible pumps 工程沈水泵用低壓單相感應電動機 |
|
|
|
CNS 7563
2021 Edition Flat Round Head RiVets Nominal Diameters 1.4 to 6 mm 扁圓頭鉚釘（標稱直徑１．４至６ｍｍ） |
|
|
|
CNS 7603
2021 Edition Varnished Terephthalate Cloth 對苯二甲酸漆布 |
|
|
|
CNS 15416-2
2021 Edition Furniture - Assessment of ignitability of upholstered furniture - Part 2: Ignition source : match-flame equiValent 家具－包襯家具燃燒性評估試驗法－第2部：燃燒源：火柴焰相當物 |
|
|
|
CNS 6048
2021 Edition Wood Blocks for Electric DeVices 配線用木台 |
|
|
|
CNS 4208
2021 Edition Inserted Nut AbrasiVe Discs and Inserted Nut Ring Wheels 螺帽嵌入式盤形及環形研磨輪 |
Translated |
|
|
CNS 16890-2
2021 Edition Air filters for general Ventilation − Part 2: Measurement of fractional efficiency and air flow resistance 一般通風用空氣濾網－第2部：區間效率與空氣流阻抗之量測 |
|
|
|
CNS 13156
2021 Edition Polyethlene insulated and polyVinyl chloride sheathed indoor telephone cables 自來水用聚乙烯夾鋁塑膠管 |
|
|
|
CNS 7094
2021 Edition Method of Micro - Hardness Test for Vickers and Knoop Hardness 維克氏及諾布氏顯微鏡下硬度試驗法 |
|
|
|
CNS 7873
2021 Edition Gear Tooth Vernier Calipers 輪齒游標卡尺 |
|
|
|
CNS 15176-14
2021 Edition Wind turbines - Part 14: Declaration of apparent sound power leVel and tonality values 風力機－第14部：視在聲功率位準及聲值之宣告 |
|
|
|
CNS 8516-1
2021 Edition Plastics − Determination of tensile properties − Part 5: Test conditions for unidirectional fibre-reinforced plastic composites 塑膠－熱塑性塑膠熔融質量流率(MFR)與熔融體積流率(MVR)之測定法－第1 部：標準方法 |
|
|
|
CNS 14793
2021 Edition Method of test for effectiVeness of pozzolans or ground blast-furnace slag in preventing excessive expansion of concrete due to the alkali-silica reaction 卜作嵐材料或高爐爐碴粉對防止鹼質與二氧化矽反應所致混凝土過度膨脹之有效性試驗法 |
|
|
|
CNS 5264
2021 Edition Method of Test for Amount of Materials in Soils Finer Than the Test SieVe 75}zYm CNS 386 土壤內顆粒小於試驗篩７５ ｍＣＮＳ３８６含量試驗法 |
|
|
|
CNS 17021-10
2021 Edition Conformity assessment − Requirements for bodies proViding audit and certification of management systems − Part 10: Competence requirements for auditing and certification of occupational health and safety management systems 符合性評鑑－機構提供管理系統稽核及驗證之要求事項－第10部：職業安全衛生管理系統稽核及驗證之適任性要求事項 |
|
|
|
CNS 15310
2021 Edition Steel slag aggregates for bituminous paVing mixtures 瀝青鋪面混合料用鋼爐碴粒料 |
|
|
|
CNS 3995
2021 Edition Method of Test for High Voltage Combination Starters 高壓綜合型起動盤檢驗法 |
|
|
|
CNS 10880-29
2021 Edition Method of Test for Paint Components-QuantitatiVe Test of Iron (Ⅲ) Oxide in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中氧化鐵（Ⅲ）之定量試驗 |
|
|
|
CNS 7009
2021 Edition Method of Test for Two-Phase SerVomotors 二相伺服電動機檢驗法 |
|
|
|
CNS 14232-15
2021 Edition Health LeVel Seven (HL7) - Part 15: Personnel management 健康資訊交換第七層協定－第１５部：人事管理 |
|
|
|
CNS 14615
2021 Edition Testing method of eValuation for package cushioning materials 包裝用緩衝材料之特性試驗法 |
|
|
|
CNS 15882
2021 Edition Fancy Veneer overlaid plywood for structural use 天然木化粧單板結構用合板 |
|
|
|
CNS 6773
2021 Edition Permissible Limits of Visual Defects for Insulating Porcelains 絕緣瓷器之外觀檢查 |
|
|
|
CNS 9224
2021 Edition Saw Blades for Woodworking, Technical Conditions of DeliVery for Bandsaw Blades 木工帶鋸片總則 |
|
|
|
CNS 6782
2021 Edition 6600 V Pin Type Insulator ６６００Ｖ裝腳絕緣器 |
|
|
|
CNS 9974
2021 Edition Water Gages for Boilers-with 10 kgf/㎠ Valves Tubular Type 鍋爐水位計–附10 kgf/㎠閥圓管型 |
|
|
|
CNS 10880-17
2021 Edition Method of Test for Paint Components-QuantitatiVe Test of Phosphoric Acid 塗料成分檢驗法–磷酸之定量 |
|
|
|
CNS 14261
2021 Edition Method of test for determining the (in-plane) flow rate per unit width and hydraulic transmissiVity of a geosynthetic using a constant head 地工合成材之定水頭橫向透水率試驗法 |
|
|
|
CNS 4064
2021 Edition Method of Test for Reinforced Concrete CoVers for Ditches (U Type) 鋼筋混凝土Ｕ形溝用蓋檢驗法 |
Translated |
|
|
CNS 6458
2021 Edition Oil of laVender (Lavandula angustifolia Mill.) 薰衣草油 |
|
| Find out:4669Items | To Page of: First -Previous-Next -Last | [13] [14] [15] [16] [17] [18] [19] |
