"LE " CNS Standards List |
|
CNS 13198
1993 Edition Fixed Multilayer Ceramic Chip Capacitors for Use in ELEctronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 13217
1993 Edition Cold RolLEd High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 4624
1993 Edition Hot-RolLEd Carbon Steel Strip for Pipes and Tubes 鋼管用熱軋碳鋼鋼帶 |
Translated |
|
|
CNS 12886-1
1993 Edition Method of Test for AcceLErated Aging of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法－120 ℃或150 ℃乾熱處理 |
Translated |
|
|
CNS 12887-1
1993 Edition Method of Test for AcceLErated Aging of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法－80 ℃及65 %R．H．濕熱處理 |
Translated |
|
|
CNS 13330
1993 Edition Dynamo Lamp for BicycLEs 自行車（腳踏車）用發電燈 |
|
|
|
CNS 13299
1993 Edition Method of Test for Trapezoid Tearing Strength of GeotextiLEs 地工織物撕裂強度試驗法（梯形法） |
|
|
|
CNS 4881
1993 Edition Tires for Industrial VehicLEs and Off the Road Service 工業車輛及工程機械用輪胎 |
Translated |
|
|
CNS 8938
1993 Edition Methods of Test for EnamelLEd Copper and Enamelled Aluminium Wires 漆包銅線及漆包鋁線檢驗法 |
|
|
|
CNS 853
1993 Edition Cross Joints With Quadri - Flange (Working Pressure LEss Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
|
|
CNS 2387
1993 Edition Method of Test for Opacity of Paper (89% RefLEctance Backing) 紙之不透明度試驗法（89 %反射率背襯） |
Translated |
|
|
CNS 739
1993 Edition Method of Test for Rubber Inner Tubes for BicycLEs 自行車用橡膠內胎檢驗法 |
|
|
|
CNS 737
1993 Edition Method of Test for Rubber Pneumatic Tires for BicycLEs 自行車用橡膠外胎檢驗法 |
Translated |
|
|
CNS 13197
1993 Edition Determination of the Image Distortion of ELEctro - Optical X - Ray Image Intensifiers 光電Ｘ射線影像加強器的影像失真之決定 |
|
|
|
CNS 4434
1993 Edition Round Nuts With DrilLEd Holes in One Face 頂孔圓螺帽 |
|
|
|
CNS 4433
1993 Edition Round Nuts With Set Pin HoLE in Side 側孔圓螺帽 |
|
|
|
CNS 5961
1993 Edition General RuLEs for Inspection of Valves 閥之檢驗總則 |
|
|
|
CNS 13194
1993 Edition Test Methods for Performance and Accuracy of DoubLE Sizers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 13214
1993 Edition Basic Environmental Testing Procedures Part 2: Tests – Test Ec: Drop and ToppLE, Primarily for Equipment - type Specimens 環境試驗法（電氣、電子）－面落下、角落下及翻倒（主要為設備）試驗法 |
|
|
|
CNS 13163
1993 Edition Method of Soundness Test for FilLEt Welds 填角熔接部之無瑕疵試驗法 |
|
|
|
CNS 5004
1992 Edition RefLEx Reflectors for Pedal Bicycles 自行車（腳踏車）用反光板 |
Translated |
|
|
CNS 13016
1992 Edition Ozonizer (Small-Sized SiLEnt Discharge Type) 臭氧（Ｏ ₃）發生器（小型無聲放電式） |
|
|
|
CNS 13004
1992 Edition Method of Welding Procedure Qualification Test for StainLEss-clad steels 不銹鋼包層鋼板熔接施工程序確認試驗法 |
|
|
|
CNS 3618
1992 Edition SingLE-Phase Induction Motors(under 100 Watt) 100瓦以下單相感應電動機 |
Translated |
|
|
CNS 13126
1992 Edition Metallic and Other Non-2organic Coatings -General RuLEs for Corrosion Tests Applicablc for Storage Conditionss 金屬和無機被覆－儲存狀態下之腐蝕試驗通則 |
|
|
|
CNS 12952
1992 Edition Method for Sampling Liquefied PetroLEum (LP) Gases 液化石油氣取樣法 |
|
|
|
CNS 13127
1992 Edition Metallic and Other Non -organic Coatings -General RuLEs for Stationary Outdoor Exposure Corrosion Tests 金屬和無機被覆－靜態戶外曝露腐蝕試驗通則 |
|
|
|
CNS 12995
1992 Edition Method of Determination for InsolubLE (free) Carbon Content of Hardmetals (Gravimetric Method) 超硬合金游離碳量測定法（重量法） |
|
|
|
CNS 1106
1992 Edition KeyhoLE Saws for Carpenter 木工用尖尾鋸 |
|
|
|
CNS 3402
1992 Edition LEtter Pads 信箋 |
Translated |
| Find out:6143Items | To Page of: First -Previous-Next -Last | [179] [180] [181] [182] [183] [184] [185] |
