"Bi " CNS Standards List| Method Test | Basic Mode | Glossary terms | Methods Illumination | Semi Finished | General Rules | Normal Type | Ergonomic principles | |
|
CNS 9389
2019 Edition Service Brake Road Test Performance Requirements for ComBinations 聯結車路段常用煞車試驗之要求性能 |
|
|
|
CNS 14130
2019 Edition Windshield wiper and washer system for automoBiles 汽車擋風玻璃用雨刷及噴洗系統 |
|
|
|
CNS 6162
2019 Edition Coolant System Hoses for AutomoBiles 汽車用冷卻水軟管 |
|
|
|
CNS 3012
2019 Edition Rivets of Brake Linings and Clutch Facings for AutomoBiles 汽車煞車襯及離合器摩擦片用鉚釘 |
|
|
|
CNS 10091
2019 Edition Method of test for ductility of Bitumen/asphalt 瀝青/柏油延性試驗法 |
|
|
|
CNS 8248
2019 Edition Method of Altitude Test of Carburetors for AutomoBiles 汽車用化油器高度性能試驗法 |
|
|
|
CNS 10161
2019 Edition Metal Tubes and TuBing for Automobiles 汽車用金屬配管 |
|
|
|
CNS 4075
2019 Edition Hydraulic Garage Jacks for AutomoBiles 汽車（修車房）用液壓千斤頂 |
Translated |
|
|
CNS 13181-2
2019 Edition The Method of Test of Presure Regulator and Vaporizers for LGP AutomoBile Fuel Systems 液化石油氣汽車燃氣系統–壓力調整器與氣化器檢驗法 |
Translated |
|
|
CNS 11062
2019 Edition Shape and Dimension of Injection Pipe Ends and Fitting for AutomoBile Diesel ENgines 汽車用柴油引擎之燃料噴射管端部及管接頭之形狀及尺度 |
|
|
|
CNS 13866
2019 Edition Location of instruments and controls for automoBiles 汽車儀表及控制器配置 |
|
|
|
CNS 11059
2019 Edition Three Dimensional Manikins for Use in Defining AutomoBile Seating Accomodations 汽車室內尺度測定用之三次元座位人體模型 |
|
|
|
CNS 3102
2019 Edition Sleeve Type Half Bearing for the Crankshaft of AutomoBile Engines 汽車引擎用套筒型半分軸承 |
Translated |
|
|
CNS 10621
2019 Edition Tyre Gauges for AutomoBiles 汽車用輪胎氣壓錶（計） |
|
|
|
CNS 9302
2019 Edition Method of Test for AraBic Gum ( for Electric Primer Uses ) 阿拉伯膠（電底火劑用）檢驗法 |
|
|
|
CNS 12176
2019 Edition Method of Test of Thermal Expansion for Brake Linings and Pads of AutomoBiles 汽車用煞車軔襯及圓盤煞車襯墊之熱膨脹試驗法 |
|
|
|
CNS 10090
2019 Edition Method of test for penetration of Bitumen/asphalt 瀝青/柏油針入度試驗法 |
|
|
|
CNS 13059-4
2019 Edition Photovoltaic devices - Part 4: Reference solar devices - Procedures for establishing calibration traceaBility 太陽光電裝置－第4部：基準太陽 裝置－建立校正追溯性之程序 |
|
|
|
CNS 7666
2019 Edition Test Code of Water Cooled Gasoline Engine for AutomoBiles 汽車用水冷式汽油引擎性能試驗法 |
|
|
|
CNS 2741
2019 Edition Method of Sand Ground Test for AutomoBiles 汽車砂地試驗法 |
|
|
|
CNS 7979
2019 Edition Glow Plugs for AutomoBiles 汽車用預熱塞 |
|
|
|
CNS 8243
2019 Edition Method of No-Load Test of Carburetors for AutomoBiles 汽車用化油器無負載性能試驗法 |
|
|
|
CNS 6812
2019 Edition Method of Test for Hot Water Heaters of AutomoBiles 汽車用熱水式暖氣機檢驗法 |
|
|
|
CNS 5319
2019 Edition Mounting Dimensions of Alternators for AutomoBiles 汽車用交流發電機安裝尺度 |
|
|
|
CNS 10332
2019 Edition Nylon Tubes for Air Brake Piping of AutomoBiles 汽車用氣煞車尼龍管 |
|
|
|
CNS 736
2019 Edition Bicycle tyres 自行車輪胎 |
|
|
|
CNS 10162
2019 Edition Method of Test for Metal Tubes and TuBing for Automobiles 汽車用金屬配管檢驗法 |
|
|
|
CNS 14622-1
2019 Edition Sterilization of health care products − Biological indicators − Part 1: General requirements 健康照護產品滅菌－生物指示劑－第1 部：一般 |
|
|
|
CNS 8389
2019 Edition Airlifts for AutomoBiles 汽車用氣動舉升器 |
|
|
|
CNS 9845
2019 Edition Reflection Type Smokemeters for Diesel AutomoBiles 柴油車用反射式排氣煙度計 |
|
| Find out:1259Items | To Page of: First -Previous-Next -Last | [14] [15] [16] [17] [18] [19] [20] |
