"Part " CNS Standards List |
|
CNS 8407-2
2020 Edition Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Phosphoric-chromic acid solution immersion test method 鋁及鋁合金之陽極氧化膜封孔度試驗法－第２部：磷酸－鉻酸溶液浸漬試驗法 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 15319-8-1
2020 Edition Sodium hydroxide for industrial use - Part 8-1: Determination of calcium content - Flame atomic absorption spectrometry 工業用氫氧化鈉－第８-１部：鈣含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 16133
2020 Edition Railway applications − Track − Switches and crossings − Part 4: Actuation, locking and detection 鐵路應用－軌道－尖軌及岔心－第4部：致動、鎖定及轍查 |
|
|
|
CNS 15820-2
2020 Edition Electric motorcycles − Safety specifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 15566-1
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors 機械安全－壓敏保護裝置－第1 部：設計及測試壓敏墊及壓敏底板之一般原則 |
|
|
|
CNS 14964-22
2020 Edition Wheelchair − Part 22: Set-up procedures 輪椅－第22部：設定程序 |
|
|
|
CNS 15200-4-5
2020 Edition Methods of test for paints - Part 4-5: Visual characteristics of film - Colorimetry (Calculation of colour differences) 塗料一般試驗法－第４－５部：塗膜視覺特性－測色（色差計算） |
|
|
|
CNS 15423-1
2020 Edition Equipment for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 8411-1
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 15200-6-1
2020 Edition Methods of test for paints - Part 6-1: Chemical property of film - Resistance to liquids 塗料一般試驗法－第6-1部：塗膜化學性質－耐液體性 |
|
|
|
CNS 15200-5-9
2020 Edition Methods of test for paints – Part 5–9: Mechanical property of film - Abrasion resistance (Rotating abrasive rubber wheel method) 塗料一般試驗法－第５－９部：塗膜機械性質：耐磨耗性(研磨輪法) |
|
|
|
CNS 15200-5-3
2020 Edition Methods of test for paints – Part 5-3: Mechanical property of film – Impact resistance test 塗料一般試驗法－第５－３部：塗膜機械性質：衝擊試驗 |
|
|
|
CNS 62040-3
2020 Edition Uninterruptible power systems (UPS) − Part 3: Method of specifying the performance and test requirements 不斷電系統(UPS)－第3 部：性能規定法及試驗要求 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 12835-3
2020 Edition Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) − Part 2: Pipes 燃氣用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 15317-2
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 2: Pipes 冷熱水輸送用交連聚乙烯管－第２部：管 |
|
|
|
CNS 15319-3
2020 Edition Sodium hydroxide for industrial use - Part 3: Determination of chlorides 工業用氫氧化鈉－第３部：氯化物含量測定法 |
|
|
|
CNS 15317-3
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 3: Fittings 冷熱水輸送用交連聚乙烯管－第３部：管件 |
|
|
|
CNS 61439-3
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 3: Distribution boards intended to be operated by ordinary persons (DBO) 低電壓開關裝置及控制裝置組裝品－第3部：由一般人員操作之配電盤(DBO) |
|
|
|
CNS 80000-9
2020 Edition Quantities and units – Part 9: Physical chemistry and molecular physics 量及單位－第9部：物理化學與分子物理學 |
|
|
|
CNS 8411-2
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
|
|
CNS 80000-1
2020 Edition Quantities and Units − Part 1: General 量及單位－第1 部：通則 |
|
|
|
CNS 15423-3
2020 Edition Equipment for water supply service – Part 3: Test methods of water hammer 自來水用器具－第3部：水鎚試驗法 |
|
|
|
CNS 15319-4
2020 Edition Sodium hydroxide for industrial use - Part 4: Determination of sodium sulfate content 工業用氫氧化鈉－第４部：硫酸鈉含量測定法 |
|
|
|
CNS 14104-3
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 15499-4
2020 Edition Electrically propelled road vehicles − Safety specifications − Part 4: Post crash electrical safety 電動推進道路車輛－安全規範第4 部：碰撞後電氣安全 |
|
|
|
CNS 15200-5-4
2020 Edition Methods of test for paints – Part 5-4: Mechanical property of film – Scratch hardness (Pencil method) 塗料一般試驗法－第５－４部：塗膜機械性質：刮痕硬度（鉛筆法） |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [14] [15] [16] [17] [18] [19] [20] |
