"3, " CNS Standards List |
|
CNS 4431
1993 Edition Square Weld Nuts 方形熔接螺帽 |
|
|
|
CNS 13135
1993 Edition Test Methods for Performance and Accuracy of Band Saws and Feed Equipment 帶鋸機及送材裝置之試驗及檢驗法 |
|
|
|
CNS 13268
1993 Edition Test Methods for Performance and Accuracy of Moulding Machine 多軸鉋機之性能試驗及精度檢驗法 |
|
|
|
CNS 13142
1993 Edition Method of Test for Ink Absorption of Paper ( K & N Ink Absorption Test ) 紙張吸墨度試驗法（K&N油墨吸收試驗法） |
Translated |
|
|
CNS 13143
1993 Edition Method of Test for Internal Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法（使用Z－方向拉／壓式試驗機） |
Translated |
|
|
CNS 4433
1993 Edition Round Nuts With Set Pin Hole in Side 側孔圓螺帽 |
|
|
|
CNS 13211
1993 Edition Audiovisual Equipment and System - Rating Plates - Marking of Electricity Supply 視聽設備與系統之電源供應額定值面板標示 |
|
|
|
CNS 3874
1993 Edition Method of Test for the Tire Valves of Bicycles 自行車（腳踏車）車胎空氣閥檢驗法 |
Translated |
|
|
CNS 13197
1993 Edition Determination of the Image Distortion of Electro - Optical X - Ray Image Intensifiers 光電Ｘ射線影像加強器的影像失真之決定 |
|
|
|
CNS 13196
1993 Edition Sampling Rate and Source Encoding for Professional Digital Audio Recording 專業數位聲頻記錄之取樣率與聲源編碼 |
|
|
|
CNS 13195
1993 Edition Audio Recording - PCM Encoder/Decoder System 聲頻記錄(脈碼調變之編碼／解碼器系統) |
|
|
|
CNS 13194
1993 Edition Test Methods for Performance and Accuracy of Double Sizers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 1326
1993 Edition Electrical Insulating Oils 電絕緣用油 |
Translated |
|
|
CNS 13193
1993 Edition Test Methods for Performance and Accuracy of Rotary Clippers 迴轉式單板截剪機之性能試驗及精度檢驗法 |
|
|
|
CNS 13192
1993 Edition Test Methods for Performance and Accuracy of Band Saw Stretchers 帶鋸片伸整機之性能試驗及精度檢驗法 |
|
|
|
CNS 13212
1993 Edition Surface Acoustic Wave (SAW) Resonators Part 1: General Information and Standard Values 表面聲波諧振器－第一部：一般性資訊及標準值 |
|
|
|
CNS 3886
1993 Edition Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理 |
Translated |
|
|
CNS 3885
1993 Edition Method of Test for Surface Treatment of Bicycle Parts 自行車（腳踏車）零件表面處理檢驗法 |
Translated |
|
|
CNS 853
1993 Edition Cross Joints With Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
|
|
CNS 3884
1993 Edition Surface Treatment for Bicycle Parts 自行車（腳踏車）零件表面處理 |
Translated |
|
|
CNS 13217
1993 Edition Cold Rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 739
1993 Edition Method of Test for Rubber Inner Tubes for Bicycles 自行車用橡膠內胎檢驗法 |
|
|
|
CNS 13216
1993 Edition Hot - rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 4432
1993 Edition Slotted Round Nuts 頂槽圓螺帽 |
|
|
|
CNS 737
1993 Edition Method of Test for Rubber Pneumatic Tires for Bicycles 自行車用橡膠外胎檢驗法 |
Translated |
|
|
CNS 13213
1993 Edition Procedures for Temperature and Irradiance Corrections to Measured I-V Characteristics of Crystalline Silicon Photovoltaic Devices 對矽晶光電元件之電流電壓特性測量值做溫度與輻射校正之程序 |
|
|
|
CNS 713
1993 Edition Cast iron flanged gate valves (10 kgf/㎠) (Inside screw non-rising stem type) 鑄鐵凸緣型閘閥(10 kgf/cm2)（閥桿非上升型） |
Translated |
|
|
CNS 3883
1993 Edition Method of Test for Coating of Bicycle Parts 自行車（腳踏車）零件塗裝檢驗法 |
Translated |
|
|
CNS 4434
1993 Edition Round Nuts With Drilled Holes in One Face 頂孔圓螺帽 |
|
|
|
CNS 3882
1993 Edition Coating for Bicycle Parts 自行車（腳踏車）零件塗裝 |
Translated |
| Find out:6360Items | To Page of: First -Previous-Next -Last | [186] [187] [188] [189] [190] [191] [192] |
