",with " CNS Standards List |
|
CNS 6763
1980 Edition Parallel Shank Counterborer with Solid Pilot 具固定導桿之柱坑鑽（圓柱柄） |
|
|
|
CNS 5977
1980 Edition High - Speed Steel Blades for Machine and Shell Reamers with Screwed - on Blades 高速鋼刀片－螺釘固定式，機用鉸刀，殼形鉸刀 |
|
|
|
CNS 5509
1980 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 5508
1980 Edition Rolling Bearings; Bearings with Spherical Outside Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
|
|
|
CNS 5106
1980 Edition Assembly Tools Screws and Nuts-Adapter for Hexagon Insert Bits for Use with Spiral Ratchet Drivers 螺釘及螺帽之裝配工具－螺旋棘輪柄六角套筒驅動接頭 |
|
|
|
CNS 4998
1979 Edition Long Shank Machine Taps with Nominal Diameters from 3 to 24 mm 長柄機力螺絲攻（標稱直徑自3 mm至24 mm） |
Translated |
|
|
CNS 228
1979 Edition 60° Center Drills，Straight Form with Conical Protective Chamfer 中心鑽（60°，去角直線錐形） |
Translated |
|
|
CNS 4228
1978 Edition Finishes with External Screw Thread for Glass Containers 玻璃容器用外螺紋 |
|
|
|
CNS 4583
1978 Edition Bolted Connections with Reduced Body; Extension Sleeves 減徑柄螺栓之結合法－伸延套筒 |
|
|
|
CNS 4216
1978 Edition Wire Twister Pliers (with Side Cutter) 扭絲鉗（附邊剪器） |
Translated |
|
|
CNS 4369
1978 Edition Round Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal Sizes 圓螺紋（具有間隙、淺螺腹，螺距為7 mm之標稱尺寸） |
|
|
|
CNS 4578
1978 Edition Bolted Connections with Reduced Booy; Metric Thread with Large Clearence, Nominal Values and Limits 減徑柄螺栓之結合法－具大間隙之公制螺紋（標稱尺寸與限界尺寸） |
|
|
|
CNS 4255
1978 Edition Spring Washers with Safety Ring 安全環彈簧墊圈 |
|
|
|
CNS 4655
1978 Edition Hexagon Set Screws with Half Dog Point and Cone End 六角頭短柱錐形端固定螺釘 |
|
|
|
CNS 4581
1978 Edition Bolted Connections with Reduced Body; Hexagon Nuts 減徑柄螺栓之結合法－六角螺帽 |
|
|
|
CNS 4371
1978 Edition Round Thread with Clearance and Steep Flank with Pitch 7 mm Theoretic Values 圓螺紋（具有間隙、深螺腹、螺距為7 mm之理論值） |
|
|
|
CNS 3610
1974 Edition Two-Flute End Mills with Straight Shank 兩刃直柄端銑刀 |
Translated |
|
|
CNS 3609
1974 Edition End Mills with Taper Shank 圓錐柄端銑刀 |
Translated |
|
|
CNS 3608
1974 Edition End Mills with Straight Shank 直柄端銑刀 |
Translated |
|
|
CNS 3613
1974 Edition Two-Flute End Mills with Taper Shank 兩刃圓錐柄端銑刀 |
Translated |
|
|
CNS 131
1972 Edition Tail Spindle (Using Morse Taper 0-6, Metric Taper 4, 6, 80-200, without Flat End) 頂針（用莫氏圓錐0-6公制圓錐4，6，80-120） |
|
|
|
CNS 123
1972 Edition Metric Taper for Tools 9-200 (with Flat End) 工具圓錐（公制圓錐 9-200)(有扁頭) |
|
|
|
CNS 124
1972 Edition Metric Taper for Tools 4-200 (Without Flat End) 工具圓錐（公制圓錐4-200）(無扁頭) |
|
|
|
CNS 125
1972 Edition Morse Taper for Tools, 0-6, Metric Taper 80-200 (with Flat End) 工具圓錐（莫氏圓錐0-6及公制圓錐80-200）(有扁頭) |
|
|
|
CNS 130
1972 Edition Morse Taper Gauge, without Flat Head 莫氏圓錐量規（無扁頭） |
|
|
|
CNS 327
1954 Edition Two-way Wrench Lever with Elliptical Handle 兩用扳柄，橢圓形桿端 |
|
|
|
CNS 326
1954 Edition Wrench Lever with Elliptical Handle 扳柄，桿端具橢圓形手把 |
|
|
|
CNS 220
1953 Edition Twist Drill, with Large Morse Taper Shank 蔴花鑽頭（莫氏圓錐柄） |
Translated |
|
|
CNS 233
1953 Edition Counter sink Drill, with Whitworth Tapping Hole 沉鑽頭（韋氏圓柱頭螺絲孔） |
Translated |
|
|
CNS 222
1953 Edition Twist Drill with Square Taper Shank (Horizontal Type) 蔴花鑽頭（方角錐，臥式） |
Translated |
| Find out:672Items | To Page of: First -Previous-Next -Last | [16] [17] [18] [19] [20] [21] [22] |
