"5 " CNS Standards List |
|
CNS 5501
1985 Edition Self - Aligning Ball Bearings: Wide Inner Race, Inner Race with Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 11357
1985 Edition Caps of Vise Jaw 虎鉗鉗口套 |
|
|
|
CNS 5989
1985 Edition Punch Holder and Die Holder for Press Dies 衝模用上模座及下模座 |
|
|
|
CNS 11356
1985 Edition Hand Operated Tube Bender 手動彎管器 |
|
|
|
CNS 11273
1985 Edition Method of Test for Fineness of Hydraulic Cement by the Test Sieve 0.045 mm CNS 386 水硬性水泥以試驗篩０．０４５ｍｍＣＮＳ３８６濕篩試驗法 |
|
|
|
CNS 5971
1985 Edition Bronze Flanged Gate Valves (10kgf/c㎡) 青銅凸緣型閘閥(10 kgf/cm2) |
|
|
|
CNS 6552
1985 Edition Test Code for Performance of Table Type Horizontal Boring Machines 床台型臥式搪床動態檢驗法 |
|
|
|
CNS 3150
1984 Edition Crowbars 撬桿 |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 2305
1984 Edition Asphalt Laminating Paper 夾層柏油紙 |
Translated |
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 2521
1984 Edition Laminated Aluminium Foils 貼合積層鋁箔 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5426
1984 Edition Multimeter 三用表 |
Translated |
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 5298
1984 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron and Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 11155
1984 Edition Grease Guns-Lever Type Hand Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 6415
1984 Edition Series of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 11154
1984 Edition Grease Guns-Rush Type Hand Guns 手用衝壓式黃油槍 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
| Find out:6646Items | To Page of: First -Previous-Next -Last | [206] [207] [208] [209] [210] [211] [212] |
