"10 " CNS Standards List |
|
CNS 14510-2
2018 Edition Information technology-Security techniques-Non-repudiation Part2:Mechanisms using symmetric techniques 資訊技術-安全技術-不可否認性-第2部:使用對稱技術之機制 |
|
|
|
CNS 15710-1
2018 Edition Effects of current on human beings and livestock − Part 1: General aspects 電流在人體及家畜上之效應－第1 部：概觀 |
|
|
|
CNS 15710-2
2018 Edition Effects of current on human beings and livestock – Part 2: Special aspects 電流在人體及家畜上之效應－第2 部：特殊觀念 |
|
|
|
CNS 2109
2018 Edition Method of Test for Domestic Use Cement Paper Sacks 內銷用水泥紙袋試驗法 |
|
|
|
CNS 10309
2018 Edition Steel Die Forgings -- Tolerances and Permissible Variations 鋼模鍛件–公差及許可差 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 10609
2018 Edition Method of Test for Portable Electric Grinders 手提電磨機試驗法 |
Translated |
|
|
CNS 1056
2018 Edition Low-voltage three-phase induction motors 低電壓三相感應電動機 |
Translated |
|
|
CNS 10923
2018 Edition Shunts and Multiple Ratio Instruments for Direct Current Use 直流用分流器及倍率器 |
|
|
|
CNS 10128
2018 Edition Scissors, Definitions 剪刀各部份名詞 |
|
|
|
CNS 10688
2018 Edition Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange - Functional Description of Interchange Circuit 資料終端設備與資料電路終端設備間互換用串列二進資料之介面–互換電路的功能敘述 |
|
|
|
CNS 10062
2018 Edition Nominal Dimension of Veneer Jointers 薄板刨邊機之標稱尺度 |
|
|
|
CNS 10912
2018 Edition Dimensions of Brushes for Electric Machines 電機用炭刷尺度 |
|
|
|
CNS 14510-1
2018 Edition Information technology - Security techniques - Non-repudiation - Part 1 : General 資訊技術－安全技術－不可否認－第１部：概述 |
|
|
|
CNS 10053
2018 Edition Nominal Dimension of Veneer Knife Grinders 平刀磨床之標稱尺寸 |
|
|
|
CNS 15156-105
2018 Edition High-voltage switchgear and controlgear - Part 105 : Alternating current switch-fuse combinations 高壓開關裝置及控制裝置－第１０５部：交流開關－熔線組合 |
|
|
|
CNS 10666
2018 Edition Disposable gas-lighter (for cigarette ignition) - Safety requirements 拋棄式打火機－安全要求 |
Translated |
|
|
CNS 11010
2018 Edition Electric storage tank water heaters 貯備型電熱水器 |
Translated |
|
|
CNS 21003-2
2018 Edition Multilayer piping systems for hot and cold water installations inside buildings − Part 2: Pipes 建築物內冷熱水裝置用多層管配管系統－第2部：管 |
|
|
|
CNS 10922
2018 Edition Method of Test for Direct-Acting Electrical Recording Instruments 直動記錄電計器試驗法 |
|
|
|
CNS 10459
2018 Edition Method of test for float test for bitumen 瀝青漂浮試驗法 |
|
|
|
CNS 10566
2018 Edition Marine Receptacles (Non-Watertight Type) 船用插座（非防水型） |
|
|
|
CNS 10416
2018 Edition Stretchy asphalt roofing felts (Synthetic fiber base) 抗拉油毛氈 |
|
|
|
CNS 14105-1
2018 Edition Information technology-Security techniques-Hash functions-Part 1:General 資訊技術–安全技術–雜湊函數–第１部：概說 |
|
|
|
CNS 10135
2018 Edition Classification of Child-Resistant Packages 防止幼童開拆之包裝分類法 |
|
|
|
CNS 10164
2018 Edition Marine Joint Boxes (Watertight Type) 船用小型接線盒（防水型） |
|
|
|
CNS 14319-10
2018 Edition Information technology-Open document architecture (ODA) and interchange format-Part 10:Formal specification 資訊技術－開放文件架構(ODA)與交換格式－第10部：正式規格 |
|
|
|
CNS 1026
2018 Edition Hand hammers 手用鋼鎚 |
|
|
|
CNS 10626
2018 Edition Marine Push Buttons 船用按鈕 |
|
|
|
CNS 10307
2018 Edition Steel Die Forgings -- Minimum Wall Thickness for Different Cross-Sectional Forms 鋼模鍛件–不同形狀剖面之最小壁厚 |
|
| Find out:1531Items | To Page of: First -Previous-Next -Last | [18] [19] [20] [21] [22] [23] [24] |
