"an " CNS Standards List |
|
CNS 9109
1987 Edition Symbols of Wiring of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖配線類符號 |
|
|
|
CNS 6032
1987 Edition Alkaline Primary Cells and Batteries 鹼性一次電池 |
|
|
|
CNS 4321
1987 Edition Hexagon Bolts with Approximately to Head, Finished and Semi-Finished, Metric Fine Thread 六角頭全螺紋螺栓（精製及半精製，公制細螺紋） |
|
|
|
CNS 12125
1987 Edition Method of Chemical analysis for Nickel -Copper Alloy 鎳銅合金分析法 |
|
|
|
CNS 12122
1987 Edition Method of Test on Communication Receivers for Amplitude-Modulation Transmissions 調幅通信接收機檢驗法 |
|
|
|
CNS 4320
1987 Edition Hexagon Head Bolts, Finished and Semi-Finished, Metric Fine Thread 六角頭螺栓（精製及半精制，公制細螺紋） |
|
|
|
CNS 5745
1987 Edition Method of test for Electrical Copper and Aluminium Wires 銅電線及鋁電線檢驗法 |
|
|
|
CNS 11836
1987 Edition Glossary of Terms Used in Iron and Steel (Products and Quality) 鋼鐵詞彙（製品及品質） |
|
|
|
CNS 8757
1987 Edition Method of Test for Bulk Specific Gravity and Density of Compacted Bituminous Mixtyres Using Paraffin- Coated Specimens 瀝青混合料壓實試體容積比重及密度試檢驗法（封臘法） |
|
|
|
CNS 9228
1987 Edition Method of Test for Dry Reed Switches (Capacitance) 乾式簧開關檢驗法（電容量） |
|
|
|
CNS 11835
1987 Edition Glossary of Terms Used in Heat Treatment of Iron and Steel 鋼鐵熱處理詞彙 |
|
|
|
CNS 9229
1987 Edition Method of Test for Dry Reed Switches (Lead Finish and Terminal Strength) 乾式簧開關檢驗法（引線表面處理與端子強度） |
|
|
|
CNS 9234
1987 Edition Method of Test for Dry Reed Switches (Standard Test Coils, Single Insulation 130 ℃ Wire) 乾式簧開關檢驗法（130℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 8226
1987 Edition Method of Test for Dry Reed Switches (Visual and Mechanical Inspection) 乾式簧開關檢驗法（目視與機械檢驗） |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 10607
1987 Edition Hair Curling Appliances 鬈髮器 |
Translated |
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 11870
1987 Edition Method of Test for Refrigerant Compressors 冷媒壓縮機試驗法 |
|
|
|
CNS 11892
1987 Edition Shears for Flower and Grass Cutting 手剪（修剪花草用） |
|
|
|
CNS 11940
1987 Edition Standard Parts of Injection Mold 塑膠型模形狀及其標準組件 |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11932
1987 Edition angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 12007
1987 Edition Method of Test for Helical Scanning Video Tape Recorders 螺線掃描錄放影機檢驗法 |
|
|
|
CNS 11999
1987 Edition Structural Steels with Specified Hardenability Bands 保證硬化能構造用鋼料（Ｈ鋼） |
|
|
|
CNS 8230
1987 Edition Method of Test for Dry Reed Switches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 11570
1986 Edition Remote Control Relays and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 11749
1986 Edition Glossary of Terms Related to Nondestructive Testing (Liquid Penetrant Testing Terms) 非破壞檢測詞彙（液滲檢測名詞） |
|
|
|
CNS 9096
1986 Edition Remote Control Transformers 遙控用變壓器 |
|
|
|
CNS 11573
1986 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-50 Sand and Dust Test) 頻率3 MHz以下電連接器檢驗法（細砂與塵埃試驗TP-50） |
|
|
|
CNS 10544
1986 Edition Test Code for Performance of Knife Grinders 鉋刀研磨機動態檢驗法 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [228] [229] [230] [231] [232] [233] [234] |
