"In " CNS Standards List |
|
CNS 14397
2017 Edition Micrographics - Graphical symbols for use In microfilming 微縮技術－縮攝用之圖形符號 |
|
|
|
CNS 8937
2017 Edition Method of Test for TravellIng Cables for Elevators 升降機用移動電纜檢驗法 |
|
|
|
CNS 5508
2017 Edition RollIng Bearings; Bearings with Spherical Outside Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
|
|
|
CNS 739
2017 Edition Method of Test for Rubber Inner Tubes for Bicycles 自行車用橡膠內胎檢驗法 |
|
|
|
CNS 11830
2017 Edition MeasurIng Methods for Light Emitting Diodes (for Indication) 發光二極體(指示用)測量法 |
|
|
|
CNS 6879
2017 Edition MachIne Taps with Reinforced Shank for Coarse ISO Metric Threads 螺絲攻（ＩＳＯ公制粗螺紋，加強柄、機用） |
|
|
|
CNS 8793
2017 Edition Method of Test for Combustion Resistance of Heat ShrInkable Tubing for Electrical Insulation 電絕緣用熱收縮套管耐燃性試驗法 |
|
|
|
CNS 5668
2017 Edition Draw - In Bolt End for Milling Machine Arbors 銑刀心軸螺栓端部 |
|
|
|
CNS 11049
2017 Edition General Rules for Radiographic TestIng 射線檢測法通則 |
|
|
|
CNS 12072
2017 Edition LocatIng Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 15210-6
2017 Edition Information technology - Radio frequency identification for item management - Part 6: Parameters for air interface communications at 860MHz to 960MHz 資訊技術─品項管理之無線射頻識別─第６部：８６０ＭＨｚ至９６０ＭＨｚ空中介面通信參數 |
|
|
|
CNS 12435
2017 Edition Pressure Sensitive AlumInum Foil Abrasive Tape for Non-Slip 電絕緣用聚酯膜黏帶 |
|
|
|
CNS 13284
2017 Edition Guide for Explosions VentIng 洩爆指導要點 |
|
|
|
CNS 5661
2017 Edition MachIne Tools Machine Tapers Morse Tapers and Metric Tapers, Taper Sockets Dimensions 工具圓錐套筒 |
|
|
|
CNS 9800
2017 Edition Product Specifications for Round Polished MonocrystallIne Gallium Arsenide Wafers 壓力容器熔接接頭之機械試驗 |
|
|
|
CNS 13635
2017 Edition Steel Butt-weldIng Pipe Fittings for Ordinary Use 一般配管用鋼製對接銲接式管件 |
|
|
|
CNS 5284
2017 Edition Addendum Modification of Spur Gears In the 0.5 System, Introduction ０．５齒制正齒輪之齒廓移位 |
|
|
|
CNS 13214
2017 Edition Basic Environmental TestIng Procedures Part 2: Tests – Test Ec: Drop and Topple, Primarily for Equipment - type Specimens 環境試驗法（電氣、電子）–面落下、角落下及翻倒（主要為設備）試驗法 |
|
|
|
CNS 5376-1
2017 Edition Iron ores —Methods for determInation of sodium content 鐵礦石—鈉定量法 |
|
|
|
CNS 12996
2017 Edition Method of DetermInation for Contents of Metallic Elements of Hardmetals by X-Ray Fluorescence (Fusion Method) 超硬合金金屬元素含量測定法–Ｘ射線螢光分析法（熔融法） |
|
|
|
CNS 9107
2017 Edition Symbols of ConnectIng of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖連接類符號 |
|
|
|
CNS 7281
2017 Edition General Rules for DetermInation of Gold and Silver in Ores 礦石中金及銀定量法總則 |
|
|
|
CNS 501
2017 Edition ISO Metric FIne Screw Threads (Diameters From 8 to 30mm and Pitches 1 to 1.25mm) 公制細螺紋4（ISO制）（標稱直徑8至30公釐，螺距1至1.25公釐） |
|
|
|
CNS 14801
2017 Edition Method of test for water resistance of material used In protective clothing (Impact penetration test) 防護衣材料防水性試驗法－衝擊穿透試驗 |
|
|
|
CNS 5059
2017 Edition SupportIng Pin and Locating Pin 支座銷與定位銷 |
|
|
|
CNS 996
2017 Edition Methods of test for resistance of glass contaIners to chemical attack 玻璃容器之耐化學侵蝕試驗法 |
|
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerations and methods of measurement,Including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
|
|
|
CNS 13784
2017 Edition General Rules for TestIng Impact Strength of Rigid Plastic by the Falling Weigth Method 硬質塑膠落錘衝擊試驗法通則 |
Translated |
|
|
CNS 4071
2017 Edition P-MethylamInophenol Sulfate (Metol) 氣動盤形輪磨機 |
Translated |
|
|
CNS 5062
2017 Edition Direction of Operation of MachIne Tool Controls 工具機之操作方向 |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [229] [230] [231] [232] [233] [234] [235] |
