"an " CNS Standards List |
|
CNS 11158
1984 Edition Tungsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 11014
1984 Edition Methods of Determination for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 10993
1984 Edition Methods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 11160
1984 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 10868
1984 Edition Method of Test for Sewing Performance of Household Zig-zag Lock Stitch Sewing Machines 家庭用錯縱縫縫紉機縫製性能試驗方法 |
|
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic analysis for Pig Iron and Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 11071
1984 Edition Emission-Spectroscopic analysis for Carbon Steel and Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
|
|
|
CNS 10786
1984 Edition Test Code for Performance of Drum Sanders 圓筒砂光機動態檢驗法 |
|
|
|
CNS 6876
1983 Edition Spindle Noses and Face Plates of Lathes 車床之主心軸鼻端及面板 |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 167
1983 Edition Double Tangential Keys 雙切線鍵 |
|
|
|
CNS 173
1983 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
|
|
CNS 169
1983 Edition Flat Fitting Keys and Sliding Cotter 配合平鍵及滑鍵 |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 8763
1983 Edition Method of Test for Micro Hardness Testing Machines for Vickers and Knoop Hardness 微小硬度試驗機檢驗法－維克氏硬度及克諾普硬度 |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 8214
1983 Edition Testing Method of Outside and Inside Diameters Wrapped Bushes for Plain Bearing 滑動軸承用捲製軸承襯檢驗法(外徑及內徑) |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [232] [233] [234] [235] [236] [237] [238] |
