"an " CNS Standards List| Information technology | Method test | Simple Type | Ovens Quartz | Hearing aids | Information technology | Information technology | Test methods | |
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 11160
1984 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 6409
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 6408
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 11112
1984 Edition Methods of Chemical analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 11155
1984 Edition Grease Guns-Lever Type Hand Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 11154
1984 Edition Grease Guns-Rush Type Hand Guns 手用衝壓式黃油槍 |
|
|
|
CNS 11071
1984 Edition Emission-Spectroscopic analysis for Carbon Steel and Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 11014
1984 Edition Methods of Determination for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 173
1983 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 169
1983 Edition Flat Fitting Keys and Sliding Cotter 配合平鍵及滑鍵 |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 167
1983 Edition Double Tangential Keys 雙切線鍵 |
|
|
|
CNS 1025
1983 Edition Hand Hammer, Dove-tail Shaped 手用鴨嘴型鋼鎚 |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 10237
1983 Edition Handles for Cranes 起重機用手柄 |
|
|
|
CNS 4647
1983 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [232] [233] [234] [235] [236] [237] [238] |
