"an " CNS Standards List |
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 11014
1984 Edition Methods of Determination for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 5280
1984 Edition Helix angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 11112
1984 Edition Methods of Chemical analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 11154
1984 Edition Grease Guns-Rush Type Hand Guns 手用衝壓式黃油槍 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 11158
1984 Edition Tungsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 11155
1984 Edition Grease Guns-Lever Type Hand Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 11160
1984 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 10151
1983 Edition Method of Test for Performance of Jig Boring Machines 工模搪床之動態檢驗法 |
|
|
|
CNS 10120
1983 Edition Method for Determining Water Content in Natural and Artificial Cryolite and Aluminium Fluoride for Industrial Use (Electrometric Method) 天然及人造冰晶石與工業用氟化鋁中水定量法（電計滴定法） |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 4410
1983 Edition Tapping Screw and Washer Assemblies 套有墊圈之自攻螺釘 |
|
|
|
CNS 10123
1983 Edition Method for Determining Phosphorus Content in Natural and Artificial Cryolite and Aluminium Fluoride for Industrial Use (Reduced Molybdophosphate Photometric Method) 天然及人造冰晶石與工業用氟化鋁中磷定量法（還原鉬磷酸鹽吸光光度法） |
|
|
|
CNS 1025
1983 Edition Hand Hammer, Dove-tail Shaped 手用鴨嘴型鋼鎚 |
|
|
|
CNS 10124
1983 Edition Method for Determining Sulphur Content in Natural and Artificial Cryolite and Aluminium Fluoride for Industrial Use (X-Ray Fluorescence Spectrometric Method) 天然及人造冰晶石與工業用氟化鋁中硫定量法(Ｘ射線螢光光譜分析法) |
|
|
|
CNS 10137
1983 Edition Standard Practice for Execution of Spun Concrete Piles 離心法製混凝土基樁施工標準 |
|
|
|
CNS 6094
1983 Edition Entrance Caps for Rigid Steel Conduit 電線用鋼管進口蓋 |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [232] [233] [234] [235] [236] [237] [238] |
