"G " CNS Standards List |
|
CNS 16149
2021 Edition Railway applications − Wheelsets and boGies − Method of specifying the structural requirements of bogie frames 鐵路應用－車輪組及轉向架－轉向架框結構之要求 |
|
|
|
CNS 15223
2021 Edition Characterisation of waste - LeachinG behaviour tests - Influence of pH on leaching with initial acid/base addition 廢棄物特性－溶出行為試驗－ｐＨ對初始酸鹼添加之溶出影響 |
|
|
|
CNS 1338
2021 Edition Method of test for suGar 蔗糖檢驗法 |
Translated |
|
|
CNS 15359
2021 Edition Standard practice for classifyinG hot-mix recycling agents 熱拌再生瀝青混凝土用再生劑分類法 |
|
|
|
CNS 2293
2021 Edition Leucaena whole plant meal (for feedinG) 銀合歡粉（飼料用） |
Translated |
|
|
CNS 1280
2021 Edition Leather - Physical and mechanical tests - Determination of shrinkaGe temperature up to 100℃ 皮革－物性及機械性能測試－100℃以下熱收縮溫度試驗法 |
|
|
|
CNS 15530
2021 Edition Methods of environmental test on liGht emitting diode systems (for general lighting service) 照明用發光二極體系統之環境試驗法 |
|
|
|
CNS 15857-1
2021 Edition Thermal performance of windows, doors and shutters − Calculation of thermal transmittance − Part 1: General 門、窗及百葉窗之熱性能－熱傳透性之計算－第1 部：一般 |
|
|
|
CNS 1323
2021 Edition Gas cylinders − Refillable welded steel cylinders for liquefied petroleum gas (LPG) − Periodic inspection and testing method 液化石油氣用可重複充填熔接鋼瓶－定期檢查及試驗法 |
|
|
|
CNS 15488
2021 Edition Method of test for veterinary druG residues in serum - Determination of multiresidue analysis of β-agonist 動物血清中動物用藥殘留量檢驗法－乙型受體素多重殘留之測定 |
|
|
|
CNS 15935
2021 Edition Standard for interconnectinG distributed resources with electric power systems 分散式電源與電力系統互聯標準 |
|
|
|
CNS 27000
2021 Edition Information technoloGy – Security techniques – Information security management systems – Overview and vocabulary 資訊技術－安全技術－資訊安全管理系統－概觀及詞彙 |
|
|
|
CNS 7868
2021 Edition Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters 產品幾何規範(GPS)－表面織構：輪廓曲線法－用語、定義及表面織構參數 |
|
|
|
CNS 3907
2021 Edition Method of Test for PluGs and Receptacles for Domestic and Similar General Use 配線用插接器試驗法 |
|
|
|
CNS 666
2021 Edition Bare hard-drawn sinGle solid copper wire 裸硬銅單電線 |
|
|
|
CNS 60335-2-17
2021 Edition Household and similar electrical appliances − Safety − Part 2-17: Particular requirements for blankets, pads, clothinG and similar flexible heating appliances 家用和類似用途電器－安全性－第2-17 部： 電熱毯、電熱墊、電熱衣及類似可撓式加熱電器之個別規定 |
|
|
|
CNS 15311
2021 Edition Method of test for potential expansion of aGgregates from hydration reactions 粒料受水合作用之潛在膨脹試驗法 |
|
|
|
CNS 13162
2021 Edition Guide for the proposal of CNS national standards 國家標準建議書格式指引 |
|
|
|
CNS 1466
2021 Edition Method of test for briGhtness measurement of directional reflectance at 457 nm of pulp, paper and board 紙漿、紙及紙板白度試驗法(方向性457nm反射率法) |
|
|
|
CNS 12491-7
2021 Edition Graphical Symbols for Use on Electrical and Electronic Equipment (Radar Control Desk,Radio Direction Finder) 電機電子設備用圖符號（雷達控制台，無線電測向儀） |
|
|
|
CNS 5000
2021 Edition Ground Thread Taps for ISO Metric Threads of Tolerances 4H to 8H and 4G to Coarse and Fine Pitches-Manufacturing Tolerances on the Threaded Portion 螺絲攻磨製螺紋公差（用於４Ｈ至８Ｈ及４Ｇ至６Ｇ之粗螺紋及細螺紋） |
|
|
|
CNS 15816-3
2021 Edition Fire resistance tests − Fire dampers for air distribution systems – Part 3: Guidance on the test method 空調系統防火閘門耐火試驗法－第3 部：試驗方法指引 |
|
|
|
CNS 17225-6
2021 Edition Solid biofuels − Fuel specifications and classes − Part 6: Graded non-wood pellets 固態生質燃料－燃料規範與等級－第6部：分級非木質顆粒 |
|
|
|
CNS 15511-21-2
2021 Edition Electric vehicle conductive charGing system − Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply − EMC requirements for off-board electric vehicle charging systems 電動車輛傳導式充電系統－第21-2部：電動車輛以傳導式連接至交流/直流電源的要求－非車載電動車輛充電系統的電磁相容要求 |
|
|
|
CNS 61439-6
2021 Edition Low-voltaGe switchgear and controlgear assemblies − Part 6: Busbar trunking systems (busways) 低電壓開關裝置及控制裝置組裝品－第6部：匯流排線槽系統(匯流排槽) |
|
|
|
CNS 13802-7
2021 Edition Graphical Symbols for Diagrams (Switchgear,Controlgear and Protective Devices) 電機工程製圖符號（開關設備、控制設備及保護設備） |
|
|
|
CNS 61850-90-7
2021 Edition Communication networks and systems for power utility automation − Part 90-7: Object models for power converters in distributed enerGy resources (DER) systems 電力公用事業自動化之通訊網路及系統— 第90-7部：分散式能源(DER)系統中電力轉換器之物件模型 |
|
|
|
CNS 8355
2021 Edition Method of Test for Electrical InsulatinG Mica Product 電絕緣用雲母製品檢驗法 |
|
|
|
CNS 1164
2021 Edition Method of test for orGanic impurities in fine aggregates 細粒料中有機不淨物含量試驗法 |
|
|
|
CNS 791
2021 Edition Basic Dimensions of 16 kGf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（16 kgf/㎠） |
|
| Find out:10068Items | To Page of: First -Previous-Next -Last | [19] [20] [21] [22] [23] [24] [25] |
