"p " CNS Standards List |
|
CNS 15832-2-2
2017 Edition Method of test for coating components − Part 2-2: Component analysis in solvent soluble matter − Softening point (Ring-and-ball method) 塗料成分試驗法－第2-2部：溶劑可溶物中成分分析－軟化點(環與球法) |
|
|
|
CNS 14677-3
2017 Edition Sound system equipment Part 3: Amplifiers 聲音系統設備－第３部：擴大機 |
|
|
|
CNS 12881
2017 Edition plastic Water Canteen 塑膠編織貼合水泥袋 |
Translated |
|
|
CNS 6219
2017 Edition High purity Nonane 高純度正壬烷 |
|
|
|
CNS 4037
2017 Edition parallel Bench Vices 鉗工虎鉗（方膛定座式） |
Translated |
|
|
CNS 14466-11
2017 Edition Audiovisual,video and television equipment and systems. Part11:Video recording systems-operation practices to facilitate browsing 視聽．影像及電視設備與系統-第１１部：影像記錄系統-用於瀏覽之操作實務 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 14659
2017 Edition Acoustics - Determination of sound power levels of noise sources using sound pressure - Comparison method in situ 聲學─利用聲壓測定噪音源聲功率位準─現場的比較法 |
|
|
|
CNS 12816-1
2017 Edition Helical-scan video tape cassette system using 12.65mm(0.5in)magnetic tape on type VHS-Part1:VHS video cassette system ＶＨＳ方式１２．６５ｍｍ（０．５ｉｎ）磁帶螺線掃描影像卡式磁帶系統-第1部:VHS及C-VHS影像磁帶系統 |
|
|
|
CNS 233
2017 Edition Counter sink Drill, with Whitworth Tapping Hole 沉鑽頭（韋氏圓柱頭螺絲孔） |
Translated |
|
|
CNS 12865-6
2017 Edition Method of Test for Digital Microelectronics ( Terminal Capacitance ) 數位微電子檢驗法（端子電容值） |
|
|
|
CNS 100
2017 Edition Accuracy Inspection of Table Type Horizontal Boring Machines 床台型臥式搪床精度檢驗 |
Translated |
|
|
CNS 13419
2017 Edition Method of Test for particle - Size Distribution of Mineral Fillers and Pigments for Paper Making 造紙用礦物質填料及顏料粒度分佈試驗法 |
Translated |
|
|
CNS 15499-2
2017 Edition Electrically propelled road vehicles – Safety specifications – Part 2: Vehicle operational safety means and protection against failures 電動推進道路車輛－安全規範－第2部:車輛操作安全方法及故障防護 |
|
|
|
CNS 13343
2017 Edition Oil Tempered Chromium Silicon Alloy Steel Wires for Springs 彈簧用油回火矽鉻合金鋼鋼線 |
|
|
|
CNS 12981
2017 Edition Method of test for milk and milk products - Determination of fat content in edible cheese 乳品檢驗法－食用乾酪脂肪含量之測定 |
|
|
|
CNS 6546
2017 Edition Guide pins of Molds for Plastics 塑膠型模用導銷 |
|
|
|
CNS 3453
2017 Edition Method of test for milk and milk products - Test of the residual antimicrobial substances in raw milk 乳品檢驗法－生乳中抗生物質殘留之檢驗 |
|
|
|
CNS 12495
2017 Edition Laboratory Beating of pulp (Beater Method) 實驗室紙漿叩解法（打漿機法） |
Translated |
|
|
CNS 2774
2017 Edition Unbleached softwood sulfate pulp (USKP) 未漂白針葉樹硫酸鹽木漿 |
|
|
|
CNS 6834-3
2017 Edition Testing methods for rubber and plastics hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 |
|
|
|
CNS 4429
2017 Edition Hexagon Nuts, Rounded Trapezoidal Thread 凸肩螺帽（公制細螺紋，圓角梯形螺紋） |
|
|
|
CNS 12806
2017 Edition Method of Bend Test for T Type Fillet Welded Joint Ｔ形填角熔接接合之彎曲試驗法 |
|
|
|
CNS 15551-4
2017 Edition Ergonomics - Accessible design - Tactile dots and bars on consumer products 人因工程－無障礙設計 - 消費產品之觸覺點及觸覺條 |
|
|
|
CNS 15996
2017 Edition plastic fuel tanks for passenger cars (replaced by CNS 14579-1) 燃氣用塑膠軟管 |
|
|
|
CNS 5030
2017 Edition project, programme and portfolio management − Guidance on programme management 凸壓電焊機 |
|
|
|
CNS 12667
2017 Edition Method of Test for Qualification of Welding procedure 熔接施工法之確認試驗法 |
|
|
|
CNS 19766
2017 Edition Information technology − Guidelines for the design of icons and symbols accessible to all users, including the elderly and persons with disabilities 資訊技術－所有年長及身心障礙使用者無障礙之圖示及符號設計指導綱要 |
|
|
|
CNS 123
2017 Edition Metric Taper for Tools 9-200 (with Flat End) 工具圓錐（公制圓錐９–２００）（有扁頭） |
|
|
|
CNS 3983
2017 Edition Method of Test for Mechanical properties of Tapping Screws 自攻螺釘之機械性質檢驗法 |
Translated |
| Find out:11004Items | To Page of: First -Previous-Next -Last | [237] [238] [239] [240] [241] [242] [243] |
