"P " CNS Standards List |
|
CNS 10513
2017 Edition Gymnastic equiPment - Hanging rings 體操設備－吊環 |
|
|
|
CNS 12495
2017 Edition Laboratory Beating of Pulp (Beater Method) 實驗室紙漿叩解法（打漿機法） |
Translated |
|
|
CNS 11764
2017 Edition Magnetic Sound Recording Reference TaPes 磁性錄音標準帶 |
|
|
|
CNS 9363
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 1 Acceleration) 頻率３ＭＨｚ以下電連接器檢驗法（加速力ＴＰ–１） |
|
|
|
CNS 7935
2017 Edition Prestressed concrete sheet piles 預力混凝土版樁 |
|
|
|
CNS 9796
2017 Edition Saddle suPported horizontal pressure vessels 以鞍座支撐之臥型壓力容器 |
|
|
|
CNS 15625-2
2017 Edition Paragliding equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics 飛行傘設備─飛行傘─第2部：飛行安全性分類要求與試驗法 |
|
|
|
CNS 3416
2017 Edition Safety Code for Power Presses (Definitions) 動力壓機安全規章（定義） |
|
|
|
CNS 12295
2017 Edition General Rules for Reliability Assured Power Type Fixed Wire Wound Resistors 可靠度保證功率型線繞固定電阻器總則 |
|
|
|
CNS 10698
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（靜音截斷、接收機動作及閉合時間） |
|
|
|
CNS 13126
2017 Edition Metallic and Other Non-2organic Coatings -General Rules for Corrosion Tests APplicablc for Storage Conditionss 金屬和無機被覆–儲存狀態下之腐蝕試驗通則 |
|
|
|
CNS 5492
2017 Edition Thread Take-uP Levers (Link Type) of Sewing Machines for Inoustrial Use 工業用縫紉機連桿式挑線桿 |
|
|
|
CNS 5030
2017 Edition Project, programme and portfolio management − Guidance on programme management 凸壓電焊機 |
|
|
|
CNS 11874
2017 Edition Fixed Mica CaPacitors ( Type CM 35 ) 雲母固定電容器（ＣＭ３５型） |
|
|
|
CNS 5162
2017 Edition Projector Lamps 投影幻燈片尺度 |
|
|
|
CNS 7777
2017 Edition Accuracy InsPection of Bench Lathes 枱式車床精度檢驗標準 |
|
|
|
CNS 10151
2017 Edition Method of Test for Performance of Jig Boring Machines 工模搪床之動態檢驗法 |
|
|
|
CNS 5293
2017 Edition Pressed Cement Roof Tiles (Arc-Pattern) 家庭用縫紉機壓布桿 |
|
|
|
CNS 5284
2017 Edition Addendum Modification of SPur Gears in the 0.5 System, Introduction ０．５齒制正齒輪之齒廓移位 |
|
|
|
CNS 8839
2017 Edition Methods of Test for Refractive Index of Chemical Products 化學製品折射率測定法 |
|
|
|
CNS 3424
2017 Edition Varnished Cotton Bias TaPe 漆斜條棉布帶 |
|
|
|
CNS 11938
2017 Edition SPrue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 15545
2017 Edition Instant coffee - Determination of free-flow and comPacted bulk densities 即溶咖啡－自由流動與緊密 堆積總體積密度測定法 |
|
|
|
CNS 4475
2017 Edition Slotted Set Screws with Full Dog Point 有槽無頭長柱端固定螺釘 |
|
|
|
CNS 3455
2017 Edition Method of test for milk and milk Products - Determination of viscosity in condensed milk 乳品檢驗法－煉乳黏度之測定 |
|
|
|
CNS 13622
2017 Edition Fixed chiP resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 4647
2017 Edition Square TaPer Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 4263
2017 Edition Cemented Carbide TiPs 碳化物刀片檢驗標準 |
|
|
|
CNS 6098
2017 Edition CouPlings for Underfloor Duct 地板電線槽接頭 |
|
|
|
CNS 15528
2017 Edition Plastic Cup ( replaced by CNS 2446 ) 塑膠吸管 |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [242] [243] [244] [245] [246] [247] [248] |
