"U " CNS Standards List |
|
CNS 14659
2017 Edition AcoUstics - Determination of sound power levels of noise sources using sound pressure - Comparison method in situ 聲學─利用聲壓測定噪音源聲功率位準─現場的比較法 |
![]() |
|
|
CNS 12741
2017 Edition BUtterfly Valves for Water Works (Short Body Type) 水道用蝶型閥(短體型) |
![]() Translated |
|
|
CNS 13163
2017 Edition Method of SoUndness Test for Fillet Welds 填角熔接部之無瑕疵試驗法 |
![]() |
|
|
CNS 5053
2017 Edition CUrved Spring Washers for Screw Assemblies 彎形彈簧墊圈(帶墊螺釘用) |
![]() |
|
|
CNS 11764
2017 Edition Magnetic SoUnd Recording Reference Tapes 磁性錄音標準帶 |
![]() |
|
|
CNS 5284
2017 Edition AddendUm Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
![]() |
|
|
CNS 2774
2017 Edition Unbleached softwood sulfate pulp (USKP) 未漂白針葉樹硫酸鹽木漿 |
![]() |
|
|
CNS 15524-4
2017 Edition Plastics - Determination of ash - Part 3: Unplasticized cellulose acetate 塑膠-灰分測定法-第4部:聚醯胺 |
![]() |
|
|
CNS 13417
2017 Edition Method of Test for Brightness for Mineral Fillers and Pigments for Paper Making (DiffUse Blue Reflectance) 造紙用礦物質填料及顏料白度試驗法(擴散藍色光反射率法) |
![]() Translated |
|
|
CNS 4608
2017 Edition StUds for Welding 螺樁(熔接用) |
![]() |
|
|
CNS 3516
2017 Edition Fixed capacitors of ceramic dielectric for Use in electronic equipment (class 1) 電子設備用陶瓷固定電容器(種類1:溫度補償用) |
![]() |
|
|
CNS 6700
2017 Edition LIGHT WIGHT RESCUE APPARATUS 簡便氧氣呼吸器 |
![]() |
|
|
CNS 15832-1-1
2017 Edition Method of test for coating components − Part 1-1: General rUle − Common test conditions 塗料成分試驗法-第1-1部:通則-一般試驗條件 |
![]() |
|
|
CNS 12254
2017 Edition QUartz Crystal Units for Oscillators (for 200-1000 kHz) 振盪器用石英振盪晶體(200KHz~1000KHz用) |
![]() |
|
|
CNS 10513
2017 Edition Gymnastic eqUipment - Hanging rings 體操設備-吊環 |
![]() |
|
|
CNS 12775
2017 Edition Low energy air gUns for recreation 低動能遊戲用槍 |
![]() Translated |
|
|
CNS 3613
2017 Edition Two-FlUte End Mills with Taper Shank 兩刃圓錐柄端銑刀 |
![]() Translated |
|
|
CNS 12807
2017 Edition QUality Requirement for Microfilm of Documents and Drawings 微縮品製作–文件及圖面微縮軟片品質之要求 |
![]() |
|
|
CNS 4429
2017 Edition Hexagon NUts, Rounded Trapezoidal Thread 凸肩螺帽(公制細螺紋,圓角梯形螺紋) |
![]() |
|
|
CNS 3873
2017 Edition Method of Test for the Rear HUbs of Bicycles 自行車(腳踏車)後輪轂檢驗法 |
![]() Translated |
|
|
CNS 12895
2017 Edition RUbber Hose Connections for Welding and Cutting Equipment 熔接與截割器(切斷器)用橡皮軟管接頭 |
![]() |
|
|
CNS 15422
2017 Edition Office fUrniture - Storage cabinets 辦公室用收納單元 |
![]() |
|
|
CNS 14182
2017 Edition Reliability and lot control tests for analog video laser transmitter and receiver modUles used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
![]() |
|
|
CNS 9114
2017 Edition Symbols of Television and Broadcast EqUipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
![]() |
|
|
CNS 6546
2017 Edition GUide Pins of Molds for Plastics 塑膠型模用導銷 |
![]() |
|
|
CNS 10899
2017 Edition Method of Test for Flat QUick-Connect Terminals 平板型接頭檢驗法 |
![]() |
|
|
CNS 9112
2017 Edition Symbols of Telephone and Bell of Interior Wiring Diagram for ArchitectUral Plans 屋內配線設計圖電話、電鈴類符號 |
![]() |
|
|
CNS 2534
2017 Edition Method of Test for NatUral Rubber Latex 天然橡膠乳液檢驗法 |
![]() Translated |
|
|
CNS 11572
2017 Edition Method of Test for Low FreqUency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test) 頻率3MHz以下電連接器檢驗法(連續性試驗TP–46) |
![]() |
|
|
CNS 2521
2017 Edition Laminated AlUminium Foils 貼合積層鋁箔 |
![]() |
Find out:11052Items | To Page of: First -Previous-Next -Last | [242] [243] [244] [245] [246] [247] [248] |