"P " CNS Standards List| Marking thermal | 660V Three | Brake Pipe | Wing Nuts | Cycles − | Manganese Dry | Wind turbines | Sodium Sulfate | |
|
CNS 12359
2017 Edition Method of Test for Fiber OPtic Devices ( FOTP-66 Measuring Relative Abrasion Resistance of Optical Waveguide Coating and Buffers) 光纖裝置檢驗法（鍍層及緩衝層耐磨性之測量ＦＯＴＰ–６６） |
|
|
|
CNS 4070
2017 Edition High SPeed Pneumatic Grinders 高速氣動輪磨機 |
Translated |
|
|
CNS 3714
2017 Edition Hand-SuPported Hair Dryers 手提型頭髮吹風機 |
Translated |
|
|
CNS 12662
2017 Edition Method of Test for Qualification Procedure of Gas Pressure Welding Technique 鑑定氣體壓力熔接技術之試驗法 |
|
|
|
CNS 12926
2017 Edition 100mm.65mm Stationary Handling OPerated Fire Water Monitor １００ｍｍ、６５ｍｍ進出水口固定型操作式消防水瞄 |
|
|
|
CNS 14800
2017 Edition Method of test for resistance of materials used in Protective clothing to penetration by blood-borne pathogens using Phi-X174 bacteriophage penetration as a test system 使用Phi-X174噬菌體穿透力之試驗系統供防護衣材料對血液媒介病原穿透阻力的試驗法 |
|
|
|
CNS 9101
2017 Edition GraPhical Symbols of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖符號總則 |
|
|
|
CNS 7351
2017 Edition SPades 一般鏟 |
|
|
|
CNS 6928
2017 Edition Method of Test for Scrub Resistance of Interior Latex Flat Wall Paints 室內用乳膠漆耐洗刷性試驗法 |
|
|
|
CNS 14182
2017 Edition Reliability and lot control tests for analog video laser transmitter and receiver modules used for oPtical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 9204
2017 Edition Method for Determining APparent Density of Metal Powders 金屬粉視密度測定法 |
|
|
|
CNS 6834-3
2017 Edition Testing methods for rubber and Plastics hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 |
|
|
|
CNS 6642
2017 Edition Calculated caPacity for unloader 卸載機之計算卸載能力 |
|
|
|
CNS 9242
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors(TP - 42 Impact) 頻率３ＭＨｚ以下電連接器檢驗法（碰撞試驗ＴＰ–４２） |
|
|
|
CNS 13143
2017 Edition Method of Test for Internal Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法（使用Ｚ–方向拉／壓式試驗機） |
Translated |
|
|
CNS 12296
2017 Edition Reliability Assured Power Type Fixed Wire Wound Resistors (S) (Established Failure Rate) 可靠度保證功率型線繞固定電阻器（特性Ｓ）（故障率設定） |
Translated |
|
|
CNS 13165
2017 Edition Method of Macro Test for Section of SPot Welded Joints 點熔接接合之斷面巨觀試驗法 |
|
|
|
CNS 5612
2017 Edition Method of test for the Permeability of fabrics to air 織物透氣度試驗法 |
|
|
|
CNS 14301-2
2017 Edition OPtical fiber cables part 2：product specifications 光纜－第二部分：產品規格 |
|
|
|
CNS 4846
2017 Edition Hexagon Head Pipe Plugs with Taper Thread 六角頭管塞（具推拔螺紋） |
|
|
|
CNS 12265
2017 Edition Method of Test for Aluminum Tri - Polyphosphate for Coating 塗料用三聚磷酸鋁檢驗法 |
|
|
|
CNS 14368
2017 Edition MicrograPhics-Recommendations for the creation of original documents 微縮技術－製作原始文件的建議 |
|
|
|
CNS 4647
2017 Edition Square TaPer Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 1103
2017 Edition OmniPotent Saws for Carpenter 木工用萬用鋸 |
Translated |
|
|
CNS 13982-15
2017 Edition Methods of test for bulk down and feather − Part 15: Determination of net fill weight 羽絨羽毛試驗法－第15部：裝填淨重測定法 |
|
|
|
CNS 5518
2017 Edition Non-insulated CrimP-type Sleeves for Copper Conductors 銅線用祼壓接套筒 |
Translated |
|
|
CNS 12839
2017 Edition Installation Methods of Power Cables Buried in Ground 電力電纜地下埋設施工法 |
|
|
|
CNS 5417
2017 Edition ComPression Tools for Wire Connectors of Interior Wiring 屋內配線用電線連接工具 |
|
|
|
CNS 13991
2017 Edition Fixed resistor networks with individually measurable resistors for use in electronic equiPment 電子設備用可單獨量測個別電阻元件之固定網路電阻器 |
|
|
|
CNS 4851
2017 Edition Screwed Sealing Plugs for Drain Fittings of High Density PE 螺旋塞（用於排水配件者，硬質聚乙烯製） |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [244] [245] [246] [247] [248] [249] [250] |
