"D C " CNS Standards List |
|
CNS 5277
2017 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 13119
2017 Edition Method of test for coefficient of static friction of paper and paperboard(Inclined plane method and horizontal plane method) 紙及紙板靜摩擦係數試驗法(傾斜平面法及水平平面法) |
|
|
|
CNS 2958
2017 Edition Cast-iron Pipes and Fittings for Sanitary Equipments 衛生設備用鑄鐵管及管件 |
|
|
|
CNS 10168
2017 Edition Methods of Measuring Case Depth for Steel 鋼之滲碳硬化層深度測定法 |
|
|
|
CNS 5770
2017 Edition General Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 5970
2017 Edition Bronze Flanged Angle Valves (10kgf/c㎡) 青銅凸緣型角閥（10 kgf/㎠） |
|
|
|
CNS 10461
2017 Edition Method of test for water repellency of textile fabrics - Spray test 織物撥水性試驗法－噴灑試驗 |
Translated |
|
|
CNS 15200-1-1
2017 Edition Testing methods for paints - Part 1-1 : General rule - General test methods (conditions and methods) 塗料一般試驗方法－第１－１部：通則－一般試驗（條件與方法） |
|
|
|
CNS 13086
2017 Edition Basic Environmental Testing procedures Part 2: Test Td: Solderability.resistance to dissolution of Metallization and to Soldering Heat of Surface Mounting Devices (SMD) 環境試驗法（電氣、電子）–表面黏著元件之焊錫性，金屬端的耐溶解性及焊錫耐熱性 |
|
|
|
CNS 9369
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 35 Proposed Insert Retention) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入扣鎖ＴＰ–３５） |
|
|
|
CNS 14467-1
2017 Edition Audio-visual, video and television equipment and systems - Part5: Control, synchronization and address codes - Chapter1: Synchronized tape/visual operating practice 視聽．影像及電視設備與系統-第５部：控制.同步及定址碼-第１章：同步磁帶/影像操作實務 |
|
|
|
CNS 12744
2017 Edition Wafer-Type Rubber-Seated Butterfly Valves 一般用蝶型閥 |
|
|
|
CNS 4225
2017 Edition Stub Metric Trapezoidal Screw Threads-Profiles 短梯形螺紋（螺紋輪廓） |
|
|
|
CNS 4224
2017 Edition Metric Trapezoidal Screw THread (Limits for Externational Screw Threads from 105 mm to 300 mm ) 梯形螺紋（標稱直徑１０５ｍｍ至３００ｍｍ的外螺紋限界尺寸） |
|
|
|
CNS 15562-6
2017 Edition Stationary training equipment − Part 6: Treadmills − Additional specific safety requirements and test methods 固定式訓練設備－第6部：跑步機－附加之特定安全要求與試驗法 |
|
|
|
CNS 16016-7
2017 Edition Plastics piping systems for hot anD Cold water installations − Polypropylene (PP) − Part 5: Fitness for purpose of the system 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第7部：符合性評鑑指引 |
|
|
|
CNS 11446-6
2017 Edition Methods of measurement on receivers for television broadcast transmission - Part 6 : Measurement under conditions different from broadcast signal standards 電視廣播傳輸接收機之量測方法-第6部 : 不同於廣播信號標準條件之量測 |
|
|
|
CNS 8352
2017 Edition Test Code for Accuracy of Numerically Controlled Knee Type Vertical Milling Machine 數值控制膝型立式銑床精度檢驗標準 |
Translated |
|
|
CNS 3916
2017 Edition Standard method for collection and measurement of dustfall (settleable particulate matter) 落塵(沉降粒狀物)收集與量測法 |
|
|
|
CNS 4426
2017 Edition Foundation Bolts 基礎螺栓 |
|
|
|
CNS 12716
2017 Edition Basic Environmental Testing Procedures - Part 2: Tests, Mounting of Components, Equipment and Articles for Dynamic Tests Including Shock (Ea), Bump (Eb), Vibration ( Fc and Fd ) and Steady - State Acceleration ( Ga ) and Guidance 環境試驗方法（電氣、電子）–動態試驗（包括衝擊、碰撞、振動及定加速度）之零組件、設備安裝方法及指南 |
|
|
|
CNS 11765
2017 Edition Method of Test for Magnetic Sound Recording Tapes 磁性錄音帶檢驗法 |
|
|
|
CNS 4232
2017 Edition Torque Type Steel Hexagon Locknuts-Mechanical and Performance Properties 扭矩式六角防鬆鋼螺帽之機械性能及性質 |
|
|
|
CNS 14866-2
2017 Edition Measurement of water flow in fully chargeD Closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 6408
2017 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算–齒廓面作用帶因數Zн |
|
|
|
CNS 11609
2017 Edition Method of Test for Unplasticized Polyvinyl Chloride Pipes with Fiberglass Reinforced Plastic Reinforcement 玻璃纖維強化塑膠加強聚氯乙烯塑膠硬質管檢驗法 |
Translated |
|
|
CNS 14257
2017 Edition Method of test for leakage rate respirator facepiece 呼吸防護具面體洩漏率試驗法 |
|
|
|
CNS 14109-1
2017 Edition Microfilming of technical drawings and other drawing office documents-Part 1:Operating procedures 技術類製圖和其他規格化製圖文件之微縮--第一部:操作程序 |
|
|
|
CNS 7797
2017 Edition Thermal spraying - Zinc, aluminum and their alloys 鋅、鋁及其合金之熔射 |
|
|
|
CNS 4556
2017 Edition Hexagon Socket HeaD Cap Screws with Reduced Height of Head 六角承窩短頭螺釘 |
Translated |
| Find out:13340Items | To Page of: First -Previous-Next -Last | [257] [258] [259] [260] [261] [262] [263] |
