"m " CNS Standards List |
|
CNS 7999
2017 Edition Oil Tempered Chromium Silicon Alloy Steel Wires for Valve Springs 閥彈簧用油回火矽鉻合金鋼鋼線 |
|
|
|
CNS 8214
2017 Edition Testing method of Outside and Inside Diameters Wrapped Bushes for Plain Bearing 滑動軸承用捲製軸承襯檢驗法（外徑及內徑） |
|
|
|
CNS 11751
2017 Edition Glossary of Tems Related to Nondestructive Testing (Radiographic Testing Terms) 非破壞檢測詞彙（射線檢測名詞） |
|
|
|
CNS 11622
2017 Edition method of Test for Fiber Length of Pulp by Projection 紙漿纖維長度投影試驗法 |
|
|
|
CNS 15077-10
2017 Edition Test conditions for machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－ 第10部：熱變形之評估 |
|
|
|
CNS 13406
2017 Edition method of Eddy Current Test for Steel Products by Encircling Coil Technique 鋼鐵產品之渦電流外繞線圈檢測法 |
|
|
|
CNS 8757
2017 Edition method of Test for Bulk Specific Gravity and Density of Compacted Bituminous Mixtyres Using Paraffin- Coated Specimens 瀝青混合料壓實試體容積比重及密度試驗法（封蠟法） |
|
|
|
CNS 14866-2
2017 Edition measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 11444
2017 Edition method of Test for Watt-Hour, Var-Hour and Maximum Demand indicators for Telemetering 瓦時，乏時及電力最大需量表示裝置（分離型）試驗法 |
|
|
|
CNS 10000
2017 Edition Wire Ropes for mechanical Control 機械控制用鋼纜 |
|
|
|
CNS 9109
2017 Edition Symbols of Wiring of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖配線類符號 |
|
|
|
CNS 13352-3
2017 Edition micrographics – Vocabulary – Part 3: Film processing 微縮技術－詞彙－第3部：軟片處理法 |
|
|
|
CNS 5653
2017 Edition method of Test for Level Gauge 水平儀檢驗法 |
|
|
|
CNS 3830
2017 Edition High manganese Steel Castings 高錳鋼鑄鋼件 |
Translated |
|
|
CNS 8839
2017 Edition methods of Test for Refractive Index of Chemical Products 化學製品折射率測定法 |
|
|
|
CNS 6152
2017 Edition method of Test for Electromechanical Switches(Electrical Endurance) 電機開關檢驗法–電耐久性 |
|
|
|
CNS 7661
2017 Edition method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 22 Life Test) 頻率３ＭＨｚ以下電連接器檢驗法（壽命試驗ＴＰ–２２） |
|
|
|
CNS 12994
2017 Edition method of Determination for total Carbon Content of Hardmetals (Gravimetric Method) 超硬合金全碳量測定法（重量法） |
|
|
|
CNS 10699
2017 Edition method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Sensitivity, Temperature and High Humidity) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻靈敏度、溫度及高濕度） |
|
|
|
CNS 7290
2017 Edition methods for Determination of Gold and Silver in Crude Bullions 粗金銀錠中金及銀定量法 |
|
|
|
CNS 12855
2017 Edition maintenance of Fire Fighting Equipment for Liquefied Petroleum Gas Device 液化石油氣設施用消防設備之維護 |
|
|
|
CNS 14492-4
2017 Edition methods of measurement on radio receivers for various classes of emission-Part4:Receivers for frequency-modulated sound broadcasting emissions 不同發射類別之無線電接收機的量測方法-第4部:調頻聲音廣播發射適用的接收機 |
|
|
|
CNS 244
2017 Edition Adjustable machine Reamer with Morse Taper Shank 機用活動鉸刀（莫氏圓錐柄） |
|
|
|
CNS 4790-3
2017 Edition Glossary of terms used in pulp and paper industry ─ General terms of paper and board 紙漿與紙詞彙─紙與紙板一般名詞 |
|
|
|
CNS 10378
2017 Edition method of Test for Folding Endurance of Paper and Paperboard (MIT Tester) 紙及紙板耐折強度試驗法（ＭＩＴ試驗機） |
Translated |
|
|
CNS 168
2017 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 15524-5
2017 Edition Plastics - Determination of ash - Part 4: Polyamides 塑膠－灰分測定法－第5部：聚氯乙烯 |
|
|
|
CNS 15523
2017 Edition Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs 機械安全—防止上肢及下肢觸及危險區域之安全距離 |
|
|
|
CNS 10522
2017 Edition Emergency Public Address Equipment 消防用緊急廣播設備 |
Translated |
|
|
CNS 9106
2017 Edition Symbols of Potential Transformers and Current Transformers of Interior Wirign Diagram for Architectural Plans 屋內配線設計圖變比器類符號 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [261] [262] [263] [264] [265] [266] [267] |
