"： " CNS Standards List |
|
CNS 15077-3
2019 Edition Test conditions for machining centres - Part 3 : Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 15748-5
2019 Edition Integrated circuits – Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 5: Measurement of conducted emissions – Workbench Faraday Cage method 積體電路－150 kHz 至1 GHz 電磁放射量測－第5 部：傳導放射量測－工作台法拉第箱體法 |
|
|
|
CNS 5346-1
2019 Edition Plastics - Symbols and abbreviated terms - Part 1:Basic polymers and their special characteristics 塑膠－縮寫用語與符號（第２部：填充材料與強化材料） |
|
|
|
CNS 15200-9-2
2019 Edition Methods of test for paints – Part 9-2: Coating powders – Inclined-plane flow test 塗料一般試驗法－第9-2 部：粉體塗料－斜面流動性試驗 |
|
|
|
CNS 15748-2
2019 Edition Integrated circuits – Measurement of electromagnetic emissions, 150 kHz to 1 GHz − Part 2: Measurement of radiated emissions − TEM cell and wideband TEM cell method 積體電路－ 150 kHz 至1 GHz 電磁放射量測－第2 部： 輻射放射量測－ 橫向電磁波室與寬頻橫向電磁波室法 |
|
|
|
CNS 14545-2
2019 Edition Fire hazard testing-part 1:Guidance for the preparation of requirements and test specifications for assessing fire hazard of electrotechnical products-Guidance for electronic components 火災危險性試驗－第１部：制定評估電氣產品之火災危險性需求及試驗內容之指引－電子零組件之指引 |
|
|
|
CNS 15200-1-5
2019 Edition Testing methods for paints - Part 1-5 : General rule - Coating of test panel (brush application) 塗料一般試驗方法－第１－５部：通則－試驗板之塗裝（刷塗） |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 13306-2-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power 射頻擾動和免疫力量測設備與量測方法－第２－２部：擾動和免疫力量測方法－擾動功率量測 |
|
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inverted vertical workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 15748-4
2019 Edition Integrated Circuits – Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 4: Measurement of conducted emissions – 1 Ω/150 Ω direct coupling method 積體電路－150 kHz 至1 GHz 電磁放射量測－第4 部：傳導放射量測－1Ω/150Ω直接耦合法積體電路－150 kHz 至1 GHz 電磁放射量測－第4 部：傳導放射量測－1Ω/150Ω直接耦合法 |
|
|
|
CNS 60245-8
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 8: Cords for applications requiring high flexibility 額定電壓450/750 V 以下橡膠絕緣電纜－第8部：高可撓性用途花線 |
|
|
|
CNS 15186-2
2019 Edition Cleanrooms and associated controlled environments – Part 2: Specifications for testing and monitoring to prove continued compliance with CNS 15186-1 潔淨室及其附屬之控制環境－第２部：確保持續符合ＣＮＳ １５１８６－１之測試與監測規範 |
|
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 15207-7
2019 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 7: Direct radio frequency (RF) power injection 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第７部：直接射頻功率注入 |
|
|
|
CNS 15593-21
2019 Edition Electricity metering − Data exchange for meter reading, tariff and load control − Part 21: Direct local data exchange 電力計量－讀表、計費及負載控制之資料交換－第21 部：直接本地資料交換 |
|
|
|
CNS 15762-5
2019 Edition Footwear − Test methods for uppers − Part 5: Thermal insulation of uppers, linings and insocks 鞋類－鞋面試驗法－第5 部：鞋面、內裡及鞋墊之隔熱性 |
|
|
|
CNS 62282-4-101
2019 Edition Fuel cell technologies − Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) − Safety of electrically powered industrial trucks 燃料電池技術－第4-101部：作為道路車輛及輔助電力單元之外的推進用燃料電池發電系統－電驅動產業搬運車之安全性 |
|
|
|
CNS 15755-5-7
2019 Edition Conversion tables for units − Part 5-7: Pressure or stress − Kilopascal and millimeter of water 單位換算表－第5-7 部：壓力或應力－千帕斯卡與毫米水柱 |
|
|
|
CNS 15755-5-6
2019 Edition Conversion tables for units − Part 5-6: Pressure or stress − Megapascal and kilogram-force per square centimeter 單位換算表－第5-6 部：壓力或應力－百萬帕斯卡與公斤力每平方公分 |
|
|
|
CNS 15200-1-6
2019 Edition Testing methods for paints - Part 1-6: General rule - Temperatures and humidities for conditioning and testing 塗料一般試驗方法－第１－６部：通則－調節與試驗之溫度及濕度 |
|
|
|
CNS 15659-2
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles − Part 2: Moisture management test 紡織品吸濕速乾性能評估－第2 部：水分傳導試驗法 |
|
|
|
CNS 13306-1-5
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration test sites for 30 MHz to 1000 MHz 射頻擾動和免疫力量測設備與量測方法－第１－５部：射頻擾動和免疫力量測設備－30 MHz至 1000 MHz之天線校正場地 |
|
|
|
CNS 15785-6
2019 Edition Tool holders with cylindrical shank − Part 6: Type E with cylindrical seat 具圓柱柄之刀具夾持器－第6 部：具圓柱形座之E 型 |
|
|
|
CNS 366-2
2019 Edition Safety requirements for bicycles − Part 2: City and trekking, young adult, mountain and racing bicycles 自行車安全要求－第2部：城市與旅行、青少年、登山及路跑自行車 |
|
|
|
CNS 13306-1-1
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus 射頻擾動和免疫力量測設備與量測方法－第１－１部：射頻擾動和免疫力量測設備－量測設備 |
|
|
|
CNS 15593-51
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 51: Application layer protocols 電力計量－讀表、計費及負載控制之資料交換－第51 部：應用層協定 |
|
|
|
CNS 15760-2
2019 Edition Footwear − General test methods – Part 2: Sampling location, preparation and duration of conditioning of samples and test pieces 鞋類－ 一般試驗法－ 第2 部： 樣品與試片之取樣部位、製備及狀態調節時間 |
|
|
|
CNS 15077-4
2019 Edition Test conditions for machining centers - Part 4 : Accuracy and repeatability of positioning of linear and rotary axes 切削中心機之檢驗條件－第４部：線性軸與旋轉軸之定位精度與重現性 |
|
| Find out:2261Items | To Page of: First -Previous-Next -Last | [22] [23] [24] [25] [26] [27] [28] |
