"An " CNS Standards List| Base Tangent | Fluxes submerged | Vocabulary Spectacle | Involute Splines | Tactile sticks | Method Test | Test method | Gaseous hydrogen | |
|
CNS 15369-2
2021 Edition Secondary batteries for the propulsion of electric road vehicles – Part 2: Dynamic discharge performAnce test and dynamic endurance test 電動車輛推進用二次電池組－第2部：動態放電性能試驗與動態耐久性試驗 |
|
|
|
CNS 15360
2021 Edition StAndard specification for mineral filler for bituminous paving mixtures 瀝青鋪面混合料用礦物填縫料 |
|
|
|
CNS 1283
2021 Edition Leather - Chemical tests - Determination of matter soluble in dichloromethAne and free fatty acid content 皮革－化性測試－二氯甲烷可溶物及游離脂肪酸含量 |
|
|
|
CNS 5346
2021 Edition Plastics − StAndard atmospheres for conditioning and testing 塑膠－縮寫用語與符號（第１部：基本聚合物與其特性） |
|
|
|
CNS 2695
2021 Edition Water-cooled Diesel Engines for LAnd Use (Small Size) 陸用小型水冷柴油發動機 |
Translated |
|
|
CNS 1164
2021 Edition Method of test for orgAnic impurities in fine aggregates 細粒料中有機不淨物含量試驗法 |
|
|
|
CNS 12633
2021 Edition Method of test for fruit And vegetable juices and drinks－Determination of glucose,fructose and sucrose by enzymatic analysis 水果及蔬菜汁飲料檢驗法－葡萄糖、果糖和蔗糖之測定（酵素法） |
|
|
|
CNS 15054
2021 Edition Fat And oil derivatives - Fatty acid methyl esters (FAME) - Determination of Ca, K, Mg and Na content by optical emission spectral analysis with inductively coupled plasma (ICP OES) 生質柴油中脂肪酸甲酯－鈣、鉀、鎂、鈉含量感應耦合電漿原子發射光譜測定法 |
|
|
|
CNS 13802-11
2021 Edition Graphical symbols for diagrams (Architectural And topographical installation plans and diagrams) 電機工程製圖符號（建築及地形學之裝置圖與製圖） |
|
|
|
CNS 15208-1
2021 Edition Linux StAndard Base (LSB) core specification 3.2 - Part 1: Generic specification Linux標準基礎核心（ＬＳＢ Ｃｏｒｅ）規格第３．２版－第１部：同屬規格 |
|
|
|
CNS 7295
2021 Edition Cocoa beAns – Determination of moisture content 可可豆－含水量測定法 |
|
|
|
CNS 15388
2021 Edition Methods of measuring rolling resistAnce for passenger car, truck and bus tyres − Single point test and correlation of measurement results 小客車、卡客車輪胎滾動阻力量測方法－單點試驗與量測結果相關性 |
|
|
|
CNS 9324
2021 Edition Feminine sAnitary napkins 衛生棉 |
|
|
|
CNS 10880-28
2021 Edition Method of Test for Paint Components-QuAntitative Test of Chromic Anhydride in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中鉻酐（三氧化鉻）之定量試驗 |
|
|
|
CNS 1280
2021 Edition Leather - Physical And mechanical tests - Determination of shrinkage temperature up to 100℃ 皮革－物性及機械性能測試－100℃以下熱收縮溫度試驗法 |
|
|
|
CNS 13802-9
2021 Edition Graphical symbols for diagrams (Telecommunication:Switching And peripheral equipment) 電機工程製圖符號（電信：交換及周邊設備） |
|
|
|
CNS 10920
2021 Edition V Belts And Pulleys for Electric Motors 電動機用三角橡膠帶及皮帶輪 |
|
|
|
CNS 7567
2021 Edition Semi - Tubular PAn Head Rivets Nominal Diameters 1.6 to 10 mm 短空心盤頭鉚釘（標稱直徑１．６至１０ｍｍ） |
|
|
|
CNS 15329-2
2021 Edition Information technology − Radio frequency identification device conformAnce test methods − Part 2: Test methods for air interface communications below 135 kHz 資訊技術－無線射頻識別裝置符合性測試方法－第2 部：低於135 kHz空中介面通信之測試方法 |
|
|
|
CNS 88
2021 Edition Classification of CNS national stAndards 國家標準之分類 |
|
|
|
CNS 15894
2021 Edition Bicycles − Chain adjusters And crank cotter pins 自行車－鏈條調整器及曲柄插銷 |
|
|
|
CNS 15807
2021 Edition Intelligent trAnsport systems − Communications access for land mobiles (CALM) − Architecture 智慧型運輸系統－陸地行動通訊接取(CALM)－架構 |
|
|
|
CNS 15489-1
2021 Edition Information And documentation - Records management - Part 1: General 資訊與文獻－檔案管理－第１部：概論 |
|
|
|
CNS 794
2021 Edition Basic Dimensions of 63 kgf/㎠ Steel Pipe FlAnges 鋼製管凸緣基準尺度（63 kgf/㎠） |
|
|
|
CNS 7398
2021 Edition Textile glass chopped strAnd mats 玻璃纖維切股氈 |
|
|
|
CNS 1046
2021 Edition Methods for chemical Analysis of Soda-Lime-Silicate glasses 鈉鈣玻璃化學分析法 |
|
|
|
CNS 15156-203
2021 Edition High-voltage switchgear And controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV 高電壓開關裝置及控制裝置－第２０３部：額定電壓超過５２ｋＶ之氣體絕緣金屬封閉型開關裝置 |
|
|
|
CNS 3648
2021 Edition Method of test for edible oils And fats－Determination of saponification value 食用油脂檢驗法－皂化價之測定 |
|
|
|
CNS 9346
2021 Edition Wheel Supports for HAnd Platform Truck 手推平車用輪架 |
|
|
|
CNS 14905-2
2021 Edition HAnd-held motor-operated electric tools - Safety - Part 2-2: Particular requirements for screwdrivers and impact wrenches 手持型電動工具－安全性－第２－２部：螺絲起子與衝擊扳手之個別規定 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [22] [23] [24] [25] [26] [27] [28] |
