"W " CNS Standards List |
|
CNS 3221
2020 Edition Methods of test for Sanitary ceramic Wares 衛生陶瓷器檢驗法 |
Translated |
|
|
CNS 5790
2020 Edition Hazard Warning Signal Flashers for Automobiles 汽車用危險警示信號燈閃光器 |
Translated |
|
|
CNS 991
2020 Edition Vitrified Grinding Wheels 瓷質燒結研磨輪 |
Translated |
|
|
CNS 15443
2020 Edition Sea Water mineral concentrate 海水濃縮礦物質液 |
|
|
|
CNS 4547
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine ScreW Threads (Tolerance Quality: Medium,Tolerances: 6H and 6h、6g)(Diameters from 2.5 to 300mm and Pitches 0.35 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（中品級–6Ｈ、6ｈ、6ｇ）（標稱直徑2.5至300mm，螺距0.35至6mm） |
|
|
|
CNS 20005
2020 Edition Information technology − Sensor netWorks − Services and interfaces supporting collaborative information processing in intelligent sensor networks 資訊技術－感測器網路－智慧感測器網路中支援協作資訊處理之服務及介面 |
|
|
|
CNS 4372
2020 Edition Round Thread With Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 8411-1
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 217
2020 Edition Tolerance of Counter - Boring TWist Drill and Shell - Type Counter - Boring Twist Drill, with Morse Taper Shank 沉孔蔴花鑽頭及空心沉孔蔴花鑽頭之尺寸公差 |
|
|
|
CNS 14964-22
2020 Edition Wheelchair − Part 22: Set-up procedures 輪椅－第22部：設定程序 |
|
|
|
CNS 8734
2020 Edition Spices and condiments − Chillies and capsicums, Whole or ground (powdered) 香辛料及調味料－全果狀或粉狀番椒與辣椒 |
|
|
|
CNS 15317-2
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold Water conveyance - Part 2: Pipes 冷熱水輸送用交連聚乙烯管－第２部：管 |
|
|
|
CNS 30128
2020 Edition Information technology − Sensor netWorks − Generic sensor network application interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 13158
2020 Edition Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipes for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管 |
Translated |
|
|
CNS 15423-3
2020 Edition Equipment for Water supply service – Part 3: Test methods of water hammer 自來水用器具－第3部：水鎚試驗法 |
|
|
|
CNS 15317-3
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold Water conveyance - Part 3: Fittings 冷熱水輸送用交連聚乙烯管－第３部：管件 |
|
|
|
CNS 152
2020 Edition Semi-Finished Washers (for Bolts with Cylindrical and pan Head and Nuts) 半光（輾光）製墊圈（用於柱頭、半圓頭螺釘及螺帽Ｍ１至Ｍ２０） |
Translated |
|
|
CNS 15200-5-9
2020 Edition Methods of test for paints – Part 5–9: Mechanical property of film - Abrasion resistance (Rotating abrasive rubber Wheel method) 塗料一般試驗法－第５－９部：塗膜機械性質：耐磨耗性(研磨輪法) |
|
|
|
CNS 4244
2020 Edition Hexagon ScreWs and Nuts-Heights of Heads and Thicknesses of Nuts 六角頭螺釘頭高及六角螺帽厚度 |
|
|
|
CNS 3-2
2020 Edition Engineering draWing (Conventional representation of machine elements) 工程製圖（機械元件習用表示法） |
|
|
|
CNS 9350
2020 Edition Bushes for Plain Bearings With Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 7030
2020 Edition Shapes and Dimensions of Fifth Wheel Coupling Pins for Semi-trailers 半拖車用第五輪聯結銷之形狀及尺度 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 7174
2020 Edition Personal eye-protection − Filters for Welding and related techniques − Transmittance requirements and recommended use 個人眼睛防護具－熔接及相關技術用濾光鏡－透光度要求及使用 |
|
|
|
CNS 11771
2020 Edition General Rules for AlloWance of Chemical Analysis and Physical Test 化學分析及物理試驗許可差總則 |
|
|
|
CNS 3965
2020 Edition Shapes and Dimensions of Grinding Wheels 研磨輪之形狀與尺度 |
|
|
|
CNS 62040-3
2020 Edition Uninterruptible poWer systems (UPS) − Part 3: Method of specifying the performance and test requirements 不斷電系統(UPS)－第3 部：性能規定法及試驗要求 |
|
|
|
CNS 358
2020 Edition Free Wheels for Bicycles 自行車（腳踏車）自由輪 |
Translated |
|
|
CNS 3220-1
2020 Edition Sanitary ceramic Ware – Tank for water closet 衛生陶瓷器－ 水箱 |
Translated |
|
|
CNS 4548
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine ScreW Threads (Tolerance Quality: Coarse,Tolerances: 7H and 8g)(Diameters from 4 to 300mm and Pitches 0.5 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（粗品級–7H、8g）（標稱直徑4至300mm，螺距0.5至6mm） |
|
| Find out:4878Items | To Page of: First -Previous-Next -Last | [22] [23] [24] [25] [26] [27] [28] |
