"men " CNS Standards List |
|
CNS 62552-1
2019 Edition Household refrigerating appliances − Characteristics and test methods − Part 1: General requirements 家用冷凍冷藏電器－特性及試驗法－第1部：一般要求 |
|
|
|
CNS 1012
2019 Edition Flow table for use in tests of hydraulic cement 水硬性水泥試驗用之流動性台 |
|
|
|
CNS 16027
2019 Edition Double-capped LED lamps − Performance requirement 雙燈帽LED 燈管－性能要求 |
Translated |
|
|
CNS 13306-1-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-2: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Conducted disturbances 射頻擾動和免疫力量測設備與量測方法－第１－２部：射頻擾動和免疫力量測設備－輔助設備－傳導干擾 |
|
|
|
CNS 15160-6
2019 Edition Acoustics - Measurement of sound insulation in buildings and of building elements - Laboratory measurements of impact sound insulation of floors 聲學－建築物及建築構件之隔音量測－樓板衝擊音隔音之實驗室量測 |
|
|
|
CNS 14843-2
2019 Edition Uninterruptible power systems (UPS)－Part 1 : General and safety requirements for UPS used in restricted access location 不斷電系統（ＵＰＳ)－第１部：使用於限制觸及區之不斷電系統安全通則 |
Translated |
|
|
CNS 61215-1-4
2019 Edition Terrestrial photovoltaic (PV) modules − Design qualification and type approval − Part 1-4: Special requirements for testing of thin-film Cu(In,Ga)(S,Se)₂ based photovoltaic (PV) modules 陸上太陽光電模組－設計確認和型式認可－第1-4部：(硫、硒)化銅(銦、鎵)薄膜型太陽光電模組特別試驗要求 |
|
|
|
CNS 15562-9
2019 Edition Stationary training equipment − Part 9: Elliptical trainers, additional specific safety requirements and test methods 固定式訓練器材－第9部：橢圓訓練機之附加特定安全要求與試驗法 |
|
|
|
CNS 784
2019 Edition Method of sampling and the amount of testing for hydraulic cement and blended hydraulic cement 水硬性水泥及水硬性混合水泥之取樣法及試驗量 |
|
|
|
CNS 8577
2019 Edition Glossary of Terms Relating to Electric Equipment for Automobiles (Sound Signalling Device System) 汽車用電器零件詞彙（音響警告系統） |
|
|
|
CNS 20349-2
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 2: Requirements and test methods for protection against risks in welding and allied processes 個人防護具－防止鑄造及熔接中風險之鞋類－第2部：防護熔接及類似製程風險之要求事項及試驗方法 |
|
|
|
CNS 1230
2019 Edition Method for making and curing concrete test specimens in laboratory 試驗室混凝土試體製作及養護法 |
|
|
|
CNS 13306-1-3
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-3: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Disturbance power 射頻擾動和免疫力量測設備與量測方法－第１－３部：射頻擾動和免疫力量測設備－輔助設備－擾動功率 |
|
|
|
CNS 15562-10
2019 Edition Stationary training equipment − Part 10: Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requirements and test methods 固定式訓練器材－第10部：具固定輪或無自由輪健身車之附加特定安全要求與試驗法 |
|
|
|
CNS 11062
2019 Edition Shape and Dimension of Injection Pipe Ends and Fitting for Automobile Diesel ENgines 汽車用柴油引擎之燃料噴射管端部及管接頭之形狀及尺度 |
|
|
|
CNS 366-2
2019 Edition Safety requirements for bicycles − Part 2: City and trekking, young adult, mountain and racing bicycles 自行車安全要求－第2部：城市與旅行、青少年、登山及路跑自行車 |
|
|
|
CNS 8572
2019 Edition Glossary of Terms Relating to Electric Equipment for Automobiles (Charging, Starting, Ignition, Preheating System) 汽車用電器零件詞彙（充電、起動、點火、預熱系統） |
|
|
|
CNS 62552-2
2019 Edition Household refrigerating appliances − Characteristics and test methods − Part 2: Performances requirements 家用冷凍冷藏電器－特性及試驗法－第2部：性能要求 |
|
|
|
CNS 14958-1
2019 Edition Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Human models, instrumentation, and procedures – Part 1: Procedure to determine the specific absorption rate (SAR) for hand-held devices used in close 人體曝露於手持式及佩戴式無線裝置之射頻場－人體模型、儀器及程序－第１部︰使用時靠近耳朵之手持式裝置（頻率介於３００ＭＨｚ至３ＧＨｚ）之比吸收率（ＳＡＲ）量測程序 |
Translated |
|
|
CNS 16080
2019 Edition Safety of primary and secondary lithium cells or batteries during transport − Test methods and requirements 一次及二次鋰單電池或電池組之運輸安全－試驗法與要求 |
|
|
|
CNS 16107-3
2019 Edition Hollow taper interface with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面－第3部：固定式刀具之刀柄尺度 |
|
|
|
CNS 16107-4
2019 Edition Hollow taper interface with flange contact surface − Part 4: Dimensions of receivers for stationary tools 具凸緣接觸面之空心錐度界面－第4部：固定式刀具用接收器之尺度 |
|
|
|
CNS 14705-3
2019 Edition Method of test for heat release rate for building materials − Part 3: Guidance on measurement 建築材料燃燒熱釋放率試驗法－第3 部：量測之指引 |
|
|
|
CNS 14587-1
2019 Edition Electromagnetic compatibility (EMC) Part 1: General-Section 1: Application and interpretation of fundamental definitions and terms 電磁相容性(EMC)--第1部:總則--第1章:術語與基本定義之應用與說明 |
|
|
|
CNS 16107-2
2019 Edition Hollow taper interface with flange contact surface − Part 2: Receivers − Dimensions 具凸緣接觸面之空心錐度界面－第2部：接收器尺度 |
|
|
|
CNS 11677
2019 Edition Furniture − Safety requirements and test methods for hazardous substance of furniture surface 家具－表面材料有害物質之安全要求及試驗法 |
|
|
|
CNS 1169
2019 Edition Method of Test for Resistance of Concrete Specimens to Rapid Freezing in Air and Rapid Thawing in Water 混凝土試體抵抗凍融試驗法（空氣中快速冰凍水中快速溶解法） |
|
|
|
CNS 15001
2019 Edition Assessment of solar ultraviolet protective fabrics 防日光紫外線織物性能評估 |
|
|
|
CNS 13301
2019 Edition Method of inspection for gas pressure welded joint of steel bars for concrete reinforcement 鋼筋混凝土用鋼筋瓦斯壓接接頭檢查法 |
|
|
|
CNS 17065
2019 Edition Conformity assessment − Requirements for bodies certifying products, processes and services 符合性評鑑－產品、過程及服務驗證機構之要求事項 |
|
| Find out:2619Items | To Page of: First -Previous-Next -Last | [22] [23] [24] [25] [26] [27] [28] |
