CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"D C " CNS Standards List

| Rubber Vibration | Test leather | Indoor air | Bolted Connections | Cone Fits | Parallel Shank | Hot pepper | Method test |

A-Civil Engineering & Architecture
CNS 12457    2017 Edition
Method of Test for Corrosion Inhibitor for Reinforsing Steel in Concrete
鋼筋混凝土用防銹劑檢驗法
C-Electrical Engineering
CNS 14675    2017 Edition
Information technology equipment - Immunity characteristics - Limits and methods of measurement
資訊技術設備-電磁抗擾力特性-限制值與量測方法
B-Mechanical Engineering
CNS 1023    2017 Edition
Wooden Handle of Picks
十字鎬用木柄
Z8-General & Miscellaneous
CNS 12663    2017 Edition
Method of Test for Radiographic anD Classification of Radiographs for Titanium Welds
鈦熔接縫放射線透射試驗法及透射照片之等級分類
B-Mechanical Engineering
CNS 5508    2017 Edition
Rolling Bearings; Bearings with Spherical Outside Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings
嵌入夾緊滾動軸承用壓製外殼
G-Ferrous Materials & Metallurgy
CNS 10171    2017 Edition
Method of 42 Percent Magnesium Chloride Stress Corrosion Test for Stainless Steels
不銹鋼之42%氯化鎂應力腐蝕試驗法
C-Electrical Engineering
CNS 6772    2017 Edition
Methods of Test for Insulating Porcelains
絕緣瓷器試驗法
A-Civil Engineering & Architecture
CNS 8902    2017 Edition
Method of Test for Oil BaseD Caulking Compounds for Building
建築用油性填縫材料檢驗法
C-Electrical Engineering
CNS 6135-4    2017 Edition
Hearing aids-Part4: Magnetic field strength in audio-frequency induction loops for hearing aid purposes
助聽器-第4部:助聽器用音頻感應迴路之磁場強度
B-Mechanical Engineering
CNS 14604    2017 Edition
Manipulating industrial robots -Automatic end effector exchange system-vocabulary and presentation of characteristics
工業用機器人-端效器自動交換系統-詞彙及特性
B-Mechanical Engineering
CNS 4646    2017 Edition
Square Taper Washers for High Prestressed I-Sections
斜墊圈(工字鐵高強度結構用)
C-Electrical Engineering
CNS 11572    2017 Edition
Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test)
頻率3MHz以下電連接器檢驗法(連續性試驗TP–46)
P-Pulp & PaperIndustry
CNS 5176    2017 Edition
Method of Determination for Wire Side and Felt Side of Paper
紙張網面與毯面測定法

Translated
K-Chemical Industry
CNS 13546-1    2017 Edition
Plastics − Methods for determining the density of non-cellular plastics − Part 3: Gas pyknometer method
塑膠-聚甲基丙烯酸甲酯(PMMA)模製及押出材料-第1部:命名系統及分類基準
Z1-Industry Safety
CNS 13350-9    2017 Edition
The Safety Code of Mechanical Parking Lot Devices (Multi Stage Type)
機械式停車場安全標準(多段式停車裝置)
L-Textile Industry
CNS 13982-6    2017 Edition
Methods of test for bulk down and feather − Part 6: Determination of the acidity (pH value)
羽絨羽毛試驗法-第6部:酸度(pH值)測定法
P-Pulp & PaperIndustry
CNS 4790-5    2017 Edition
Glossary of terms used in pulp and paper industry ─ Terms of pulp, paper or board properties
紙漿與紙詞彙─紙漿、紙或紙板之性質及試驗名詞
S-Domestic Wares
CNS 15625-2    2017 Edition
Paragliding equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics
飛行傘設備─飛行傘─第2部:飛行安全性分類要求與試驗法
K-Chemical Industry
CNS 769    2017 Edition
Method of Test for Boiled Linseed Oil
熟煉亞麻仁油檢驗法

Translated
Z9-General & Miscellaneous
CNS 14369    2017 Edition
Micrographics-Reader-printers for transparent microforms-Characteristics
微縮技術-透明微縮品閱讀影印機-特性
Z2-Industry Safety
CNS 16020    2017 Edition
Respiratory protective devices − Powered filtering devices incorporating a helmet or a hood – Requirements, testing, marking
呼吸防護裝置-結合頭盔或頭套之動力過濾裝置-要求、試驗、標示
P-Pulp & PaperIndustry
CNS 1358    2017 Edition
Method of Test for Folding Endurance of Paper by Schopper type Tester
紙之蕭波式耐折強度試驗法

Translated
Z7-General & Miscellaneous
CNS 14711    2017 Edition
Metallic and other non- organic coatings-Sulfur dioxide test with general condensation of moisture
金屬及其他無機被覆層-含凝結水氣之二氧化硫腐蝕試驗法
B-Mechanical Engineering
CNS 5989    2017 Edition
Pumps – Testing – Submersible mixers for wastewater and similar applications
衝模用上模座及下模座
B-Mechanical Engineering
CNS 4191    2017 Edition
Assembly tools for screws and nuts - Universal joints for hand-operated square drive socket wrenches
螺釘及螺帽之裝配工具–手動套筒扳手用萬向接頭
B-Mechanical Engineering
CNS 512    2017 Edition
Metric Trapezoidal Screw Thread (Genral Plan)
梯形螺紋(總則)
C-Electrical Engineering
CNS 15549    2017 Edition
Methods of measurement of touch current and protective conductor current
接觸電流與保護導體電流之量測法
Z1-Industry Safety
CNS 13350-10    2017 Edition
The Safety Code of Mechanical Parking Lot Devices (Elevator Sliding Type)
機械式停車場安全標準(升降滑動式)
C-Electrical Engineering
CNS 15535    2017 Edition
Fluorescent induction lamps - Safety requirements
感應式螢光燈-安全性要求
K-Chemical Industry
CNS 6834-5    2017 Edition
Testing methods for rubber and plastics hoses - Part 5: Determination of electrical resistance anD Conductivity
橡膠管及塑膠管試驗法-第5部:電阻與導電係數之測定

Find out:13340Items   |  To Page of: First -Previous-Next -Last  | [268] [269] [270] [271] [272] [273] [274]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.