"： " CNS Standards List |
|
CNS 60669-2-3
2019 Edition Switches for household and similar fixed electrical installations − Part 2-3: Particular requirements − Time-delay switches (TDS) 家用和類似用途固定式電氣裝置之開關－第2-3部：延時開關(TDS)之個別要求 |
|
|
|
CNS 15199
2019 Edition Electrical installations of buildings - Part 7-712: Requirements for special installations or locations - Solar photovoltaic (PV) power supply systems 建築物之電力安裝－第７－７１２部：特別設立或地點之要求－太陽光電電力供應系統 |
|
|
|
CNS 12514-7
2019 Edition Fire-resistance tests – Elements of building construction – Part 7: Specific requirements for columns 建築物構造構件耐火試驗法－第7 部：柱特定要求 |
|
|
|
CNS 62282-7-2
2019 Edition Fuel cell technologies − Part 7-2: Test methods − Single cell and stack performance tests for solid oxide fuel cells (SOFC) 燃料電池技術－第7-2部：試驗方法－固態氧化物燃料電池(SOFC)單電池及電池組性能試驗 |
|
|
|
CNS 15125-1
2019 Edition Solar heating - Domestic water heating systems - Part 1 : Performance rating procedure using indoor test methods 太陽能加熱－家用熱水系統－第１部：性能評比程序之室內試驗法 |
|
|
|
CNS 16083-2
2019 Edition Viscosity and viscometric fixed points of glass − Part 2: Determination of annealing point and strain point by fiber elongation 玻璃黏度和黏度固定點－第2部：以玻璃絲拉伸法測定退火點和應變點 |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 15076-2
2019 Edition Modular units for machine tools - Workholding pallets - Part 2 : Workholding pallets of nominal size greater than 800 mm 工具機之模組單元－工件固定托板－第２部：標稱尺度８００ｍｍ以上之工件固定托板 |
|
|
|
CNS 14498-1
2019 Edition Road vehicles - Electrical disturbances from conduction and coupling - Part 1：Definitions and general consideration 道路車輛—經由傳導及耦合之電擾動－第1部：定義及通則 |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 13306-2-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power 射頻擾動和免疫力量測設備與量測方法－第２－２部：擾動和免疫力量測方法－擾動功率量測 |
|
|
|
CNS 14545-4
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 0:Glow-wire test methods-General 火災危險性試驗－第２部：試驗方法－第１章／第０單元：熾熱線試驗方法－通則 |
|
|
|
CNS 15593-21
2019 Edition Electricity metering − Data exchange for meter reading, tariff and load control − Part 21: Direct local data exchange 電力計量－讀表、計費及負載控制之資料交換－第21 部：直接本地資料交換 |
|
|
|
CNS 5346-2
2019 Edition Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials 塑膠－縮寫用語與符號（第３部：可塑劑） |
|
|
|
CNS 14943
2019 Edition Essential oils – General guidance on chromatographic profiles – Part 1: Preparation of chromatographic profiles for presentation in standards 精油—層析特性成分分布通則－第1部：標準中層析特性成分分布之建立 |
|
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 15187-2-1
2019 Edition Low-voltage fuses - Part 2-1: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Section I to VI: Examples of types of standardized fuses 低壓熔線－第２－１部：專業人員用熔線之補充規定（以工業用為主之熔線）－第Ｉ至ＶＩ章：經標準化之熔線各種類型範例 |
|
|
|
CNS 61347-2-13
2019 Edition Lamp controlgear − Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules 光源控制裝置－第2-13部：LED模組用直流或交流電子式控制裝置之個別要求 |
|
|
|
CNS 14545-5
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 15593-31
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 31: Use of local area networks on twisted pair with carrier signalling 電力計量－ 讀表、計費及負載控制之資料交換－ 第31 部： 使用雙絞線載波信號之區域網路 |
|
|
|
CNS 15077-3
2019 Edition Test conditions for machining centres - Part 3 : Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 15646-2
2019 Edition Rigid cellular plastics – Determination of flexural properties – Part 2: Detrmination of flexural strength and apparent flexural modulus of elasticity 硬質發泡塑膠－彎曲性能測定法－第2 部：彎曲強度與視彎曲彈性係數測定法 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 15755-5-8
2019 Edition Conversion tables for units − Part 5-8: Pressure or stress − Kilopascal and millimeter of mercury 單位換算表－第5-8 部：壓力或應力－千帕斯卡與毫米汞柱 |
|
|
|
CNS 60335-2-7
2019 Edition Household and similar electrical appliances − Safety − Part 2-7: Particular requirements for washing machines 家用和類似用途電器－安全性－第2-7 部：洗衣機之個別規定 |
|
|
|
CNS 15659-2
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles − Part 2: Moisture management test 紡織品吸濕速乾性能評估－第2 部：水分傳導試驗法 |
|
|
|
CNS 15094-1
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - Part 1: Removal of nitric oxide 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第1部：氮氧化物去除性能 |
|
|
|
CNS 60669-2-4
2019 Edition Switches for household and similar fixed electrical installations − Part 2-4: Particular requirements − Isolating switches 家用和類似用途固定式電氣裝置之開關－第2-4部：隔離開關之個別要求 |
|
|
|
CNS 15327-3
2019 Edition Information technology − Automatic identification and data capture techniques − Unique identification − Part 3: Common rules 資訊技術－自動識別及資料擷取技術－唯一識別－第3部：共同規則 |
|
| Find out:2261Items | To Page of: First -Previous-Next -Last | [23] [24] [25] [26] [27] [28] [29] |
