"： " CNS Standards List |
|
CNS 15077-8
2019 Edition Test conditions for machining centers - Part 8 : Evaluation of contouring performance in the three coordinate planes 切削中心機之檢驗條件－第８部：在三個坐標平面內之輪廓性能評估 |
|
|
|
CNS 14816-1
2019 Edition Low-voltage switchgear and controlgear − Part 1: General rules 低電壓開關裝置及控制裝置－第1部：通則 |
|
|
|
CNS 15760-3
2019 Edition Footwear − General test methods – Part 3: Ageing conditioning 鞋類－一般試驗法－第3 部：老化調節 |
|
|
|
CNS 15760-2
2019 Edition Footwear − General test methods – Part 2: Sampling location, preparation and duration of conditioning of samples and test pieces 鞋類－ 一般試驗法－ 第2 部： 樣品與試片之取樣部位、製備及狀態調節時間 |
|
|
|
CNS 14498-1
2019 Edition Road vehicles - Electrical disturbances from conduction and coupling - Part 1：Definitions and general consideration 道路車輛—經由傳導及耦合之電擾動－第1部：定義及通則 |
|
|
|
CNS 15094-4
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - Part 4: Removal of formaldehyde 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第4部：甲醛去除性能 |
|
|
|
CNS 29182-5
2019 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 5: Interface definitions 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第5部：介面定義 |
|
|
|
CNS 15125-1
2019 Edition Solar heating - Domestic water heating systems - Part 1 : Performance rating procedure using indoor test methods 太陽能加熱－家用熱水系統－第１部：性能評比程序之室內試驗法 |
|
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 15646-2
2019 Edition Rigid cellular plastics – Determination of flexural properties – Part 2: Detrmination of flexural strength and apparent flexural modulus of elasticity 硬質發泡塑膠－彎曲性能測定法－第2 部：彎曲強度與視彎曲彈性係數測定法 |
|
|
|
CNS 15785-6
2019 Edition Tool holders with cylindrical shank − Part 6: Type E with cylindrical seat 具圓柱柄之刀具夾持器－第6 部：具圓柱形座之E 型 |
|
|
|
CNS 15199
2019 Edition Electrical installations of buildings - Part 7-712: Requirements for special installations or locations - Solar photovoltaic (PV) power supply systems 建築物之電力安裝－第７－７１２部：特別設立或地點之要求－太陽光電電力供應系統 |
|
|
|
CNS 15076-2
2019 Edition Modular units for machine tools - Workholding pallets - Part 2 : Workholding pallets of nominal size greater than 800 mm 工具機之模組單元－工件固定托板－第２部：標稱尺度８００ｍｍ以上之工件固定托板 |
|
|
|
CNS 7779-3
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions − Part 3: Enveloping surface methods 工業用風機－在標準化實驗室條件下風機聲功率位準測定－第3 部：包絡面法 |
|
|
|
CNS 15593-21
2019 Edition Electricity metering − Data exchange for meter reading, tariff and load control − Part 21: Direct local data exchange 電力計量－讀表、計費及負載控制之資料交換－第21 部：直接本地資料交換 |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 15755-5-8
2019 Edition Conversion tables for units − Part 5-8: Pressure or stress − Kilopascal and millimeter of mercury 單位換算表－第5-8 部：壓力或應力－千帕斯卡與毫米汞柱 |
|
|
|
CNS 16083-2
2019 Edition Viscosity and viscometric fixed points of glass − Part 2: Determination of annealing point and strain point by fiber elongation 玻璃黏度和黏度固定點－第2部：以玻璃絲拉伸法測定退火點和應變點 |
|
|
|
CNS 60669-2-3
2019 Edition Switches for household and similar fixed electrical installations − Part 2-3: Particular requirements − Time-delay switches (TDS) 家用和類似用途固定式電氣裝置之開關－第2-3部：延時開關(TDS)之個別要求 |
|
|
|
CNS 60669-2-4
2019 Edition Switches for household and similar fixed electrical installations − Part 2-4: Particular requirements − Isolating switches 家用和類似用途固定式電氣裝置之開關－第2-4部：隔離開關之個別要求 |
|
|
|
CNS 15094-1
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - Part 1: Removal of nitric oxide 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第1部：氮氧化物去除性能 |
|
|
|
CNS 15064-1
2019 Edition Solar energy - Reference solar spectral irradiance at the ground at different receiving conditions - Part 1: Direct normal and hemispherical solar irradiance for air mass 1.5 太陽能－在不同地球表面接收狀況下之參考太陽光譜照射度－第１部：大氣光程１﹒５下之直接垂直與半球太陽照射度 |
|
|
|
CNS 15755-6-2
2019 Edition Conversion tables for units − Part 6-2: Work − Watt hour and kilocalorie 單位換算表－第6-2 部：功－瓦特小時與千卡 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 14943
2019 Edition Essential oils – General guidance on chromatographic profiles – Part 1: Preparation of chromatographic profiles for presentation in standards 精油—層析特性成分分布通則－第1部：標準中層析特性成分分布之建立 |
|
|
|
CNS 7705
2019 Edition Leather − Determination of flex resistance − Part 1: Flexometer method 皮革－耐撓性測定－第1部：撓度計法 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 13059-10
2019 Edition Photovoltaic devices − Part 10: Methods of linearity measurement 太陽光電裝置－第10 部：線性度量測法 |
|
|
|
CNS 15014-3
2019 Edition Software engineering - Product evaluation - Part 3: Process for developers 軟體工程－產品評估－第３部：發展者過程 |
|
|
|
CNS 15711-1
2019 Edition Photovoltaic (PV) module performance testing and energy rating − Part 1: Irradiance and temperature performance measurements and power rating 太陽光電模組性能試驗與能量定額－第1 部： 照射度與溫度性能量測及功率定額 |
|
| Find out:2261Items | To Page of: First -Previous-Next -Last | [23] [24] [25] [26] [27] [28] [29] |
