"O " CNS Standards List| Fastening Taper | Shuttle Raceing | Calculation Load | Essential oils | Viscose Rayon | Viscose Rayon | Pin Allocations | Sodium carbonate | |
|
CNS 62752
2021 Edition In-cable cOntrol and protection device for mode 2 charging of electric road vehicles (IC-CPD) 電動車輛充電模式2之纜線上控制及保護裝置 |
|
|
|
CNS 12388
2021 Edition MethOd of practice for sampling bituminous paving mixtures 瀝青鋪面混合料取樣法 |
|
|
|
CNS 15218
2021 Edition AcOustics - Sound absorbers for use in buildings - Rating of sound absorption 聲學－建築物使用之吸音材－吸音量評定 |
|
|
|
CNS 9100
2021 Edition General Rule fOr Panelboard 分電盤總則 |
|
|
|
CNS 2343
2021 Edition Milk pOwders and cream powder 乳粉(奶粉)及乳脂粉 |
|
|
|
CNS 61
2021 Edition POrtland blast-furnace slag cement ( replaced by CNS 15286 ) 卜特蘭水泥 |
Translated |
|
|
CNS 15783-1
2021 Edition LOw-voltage switchgear and controlgear assemblies – Part 1: General rules 低電壓開關裝置及控制裝置組裝品－第1部：一般規則 |
|
|
|
CNS 8906
2021 Edition POlyvinyl Chloride Corrugated Sheet 聚氯乙烯系地磚 |
|
|
|
CNS 15920
2021 Edition Plastics pipes and fittings − Peel decOhesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm 塑膠管及管件－聚乙烯(PE)管/管或管/管件熱熔對接之組合試件製備 |
|
|
|
CNS 20346
2021 Edition PersOnal protective equipment − Protective footwear 個人防護具－防護鞋 |
|
|
|
CNS 12549
2021 Edition GrOund granulated blast-furnace slag for use in concrete and mortars 混凝土及水泥砂漿用水淬高爐爐碴粉 |
|
|
|
CNS 15493
2021 Edition Safety requirements Of plastic puzzle ground mat 拼接塑膠地墊之安全要求 |
Translated |
|
|
CNS 8503
2021 Edition RecOmmended practice for hot dip galvanized coatings 熱浸鍍鋅作業方法 |
|
|
|
CNS 12698
2021 Edition Unplasticized POlyvinyl Chloride Pipes for Raft 管筏用聚氯乙烯硬質塑膠管 |
Translated |
|
|
CNS 1002-1-2
2021 Edition HydrOchloric acid for industrial use - Part 1-2: Determination of total acidity - Potentiometric method 工業用氫氯酸－第１－２部：總酸度測定法－電位差滴定法 |
|
|
|
CNS 5000
2021 Edition GrOund Thread Taps for ISO Metric Threads of Tolerances 4H to 8H and 4G to Coarse and Fine Pitches-Manufacturing Tolerances on the Threaded Portion 螺絲攻磨製螺紋公差（用於４Ｈ至８Ｈ及４Ｇ至６Ｇ之粗螺紋及細螺紋） |
|
|
|
CNS 15314
2021 Edition Standard classificatiOn for sizes of aggregate for road and bridge construction 道路及橋樑施工用粒料尺度分類 |
|
|
|
CNS 14064-1
2021 Edition GreenhOuse gases − Part 1: Specification with guidance at the organization level for quantification and reporting of greenhouse gas emissions and removals 溫室氣體－第1部：組織層級溫室氣體排放與移除量化及報告附指引之規範 |
|
|
|
CNS 3085
2021 Edition MethOd of test for holocellulose in wood 木材全纖維素試驗法 |
|
|
|
CNS 10325
2021 Edition DimensiOns of Low - Voltage Three - Phase Squirrel - Cage Induction Motors (for Special Frame, flange Type) 低壓三相鼠籠型感應電動機標準尺度（特殊框號用，凸緣式） |
|
|
|
CNS 12491-9
2021 Edition Graphical SymbOls for Use on Electrical and Electronic Equipment (Recording,Reproducing) 電機電子設備用圖符號（記錄，重現） |
|
|
|
CNS 5091
2021 Edition MethOd of Laboratory Determination of Moisture Content of Soil 實驗室土壤含水量測定法 |
|
|
|
CNS 10808
2021 Edition Ductile irOn pipes + Amendment 1 延性鑄鐵管+補充增修1 |
|
|
|
CNS 14703
2021 Edition MethOd of test for water-soluble chloride in mortar and concrete 硬固水泥砂漿及混凝土中水溶性氯離子含量試驗法 |
|
|
|
CNS 13333-1
2021 Edition Plastics − InjectiOn moulding of test specimens of thermoplastic materials − Part 5: Preparation of standard specimens for investigating anisotropy 塑膠－ 非發泡塑膠之密度測定法－第1 部：浸漬法、液體比重瓶法及滴定法 |
|
|
|
CNS 13961
2021 Edition Mixing water Of concrete 混凝土拌和用水 |
|
|
|
CNS 15450
2021 Edition Testing methOd for chemical emission rates from electronic equipment 電器設備化學逸散率試驗法 |
|
|
|
CNS 3647
2021 Edition MethOds of test for edible oils and fats－Determination of acid value 食用油脂檢驗法－酸價之測定 |
|
|
|
CNS 3376-17
2021 Edition Electrical apparatus fOr explosive gas atmospheres - Part 17: Inspection and maintenance of electrical installations in hazardous areas (other than mines) 爆炸性氣體環境用電機設備－第１７部：安裝於危險區域電機設備之檢查和維護（不包含礦坑用） |
|
|
|
CNS 7477
2021 Edition Aluminium dOors 鋁合金製門 |
|
| Find out:15086Items | To Page of: First -Previous-Next -Last | [23] [24] [25] [26] [27] [28] [29] |
