"ol " CNS Standards List |
|
CNS 61439-4
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 4: Particular requirements for assemblies for construction sites (ACS) 低電壓開關裝置及控制裝置組裝品－第4部：建築工地用組裝品(ACS)之個別要求 |
|
|
|
CNS 30128
2020 Edition Information technology − Sensor networks − Generic sensor network application interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 24508
2020 Edition Ergonomics − Accessible design − Guidelines for designing tactile symbols and characters 人因工程學－無障礙設計－觸覺符號與字符之設計指導綱要 |
|
|
|
CNS 13137
2020 Edition Safety Standards for Construction of Band Saws With Rollers 送材輪進給式帶鋸機之構造安全基準 |
|
|
|
CNS 1860
2020 Edition Phosphomolybdic Acid 化學試藥（磷鉬酸） |
|
|
|
CNS 14797
2020 Edition Mineral spirits（hydrocarbon dry cleaning solvent,petroleum spirits,stoddard solvent） 礦物型溶劑 |
|
|
|
CNS 5270-7
2020 Edition Graphical Symbols for Fluid Power Diagrams-Directional Control Valve 液壓、氣壓圖形符號–方向控制閥 |
|
|
|
CNS 15809
2020 Edition Personal eye-protection – Ultraviolet filters – Transmittance requirements and recommended use 個人眼睛防護具－紫外線濾光鏡－透光度要求及使用 |
|
|
|
CNS 5270-8
2020 Edition Graphical Symbols for Fluid Power Diagrams-Check Valve 液壓、氣壓圖形符號–止回閥 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 1859
2020 Edition Phloroglucinol (1,3,5-Trihydroxybenzene) 化學試藥（１，３，５苯三酚） |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 781
2020 Edition oleoresinous Antifouling Paint for Steel Ship Bottom 鋼船用油性船底防污漆 |
Translated |
|
|
CNS 9567
2020 Edition Withdrawal Sleeves for Rolling Bearings 滾動軸承拔出套筒 |
|
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 4242
2020 Edition Widths Across Flats and Widths Across Corners for Bolts, Screws and Nuts 螺栓、螺釘、螺帽之對面寬度及對角寬度 |
|
|
|
CNS 120
2020 Edition Collar (Using Light Duty Set Screw) 頸圈（用螺絲銷、輕型） |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 5270-1
2020 Edition Graphical Symbols for Fluid Power Dizgrams-Line and Connection 液壓、氣壓圖形符號–管路及連接 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 1851
2020 Edition Phenol (Reagent) 酚（試藥） |
|
|
|
CNS 8483
2020 Edition Control Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 5007
2020 Edition Rotating Tools with Parallel Shanks-Diameters of Shanks and Sizes Driving Squares 直柄旋轉刀具之柄徑及驅動方頭之尺寸 |
|
|
|
CNS 10023
2020 Edition Plutonium By Controlled - Potential Coulometry 布層心體橡膠輸送帶 |
|
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 79
2020 Edition Minimum Distance Across Hexagonal Bolts 螺釘間之最小距離（適用於六角螺釘及螺帽） |
|
|
|
CNS 9568
2020 Edition Adapter Sleeves for Rolling Bearings 滾動軸承套接套筒（附螺帽與鎖緊墊圈） |
|
|
|
CNS 12983
2020 Edition Standard Substances for Volumetric Analysis 容量分析用標準試藥 |
|
|
|
CNS 20005
2020 Edition Information technology − Sensor networks − Services and interfaces supporting collaborative information processing in intelligent sensor networks 資訊技術－感測器網路－智慧感測器網路中支援協作資訊處理之服務及介面 |
|
| Find out:3988Items | To Page of: First -Previous-Next -Last | [23] [24] [25] [26] [27] [28] [29] |
