"D C " CNS Standards List |
|
CNS 10114
2017 Edition Method for Determining Iron Content in Natural and Artificial Cryolite (1,10-Phenanthroline Photometric Method) 天然及人造冰晶石中鐵定量法(二氮雜菲吸光光度法) |
![]() |
|
|
CNS 13068
2017 Edition Methods of test for total amine values of amine-based hardeners of epoxy resins 環氧樹脂之胺系硬化劑總胺價試驗法 |
![]() Translated |
|
|
CNS 195
2017 Edition LiquiD Carbon dioxide 液態二氧化碳 |
![]() |
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
![]() |
|
|
CNS 5494
2017 Edition Needle Bar Connecting Links of Sewing Machines for Industrial Use 工業用縫紉機針棒連桿 |
![]() |
|
|
CNS 4573
2017 Edition Slotted RaiseD Countersunk Bolts for Drawing Instruments 有槽扁圓頂埋頭螺栓(繪圖儀器用) |
![]() |
|
|
CNS 5492
2017 Edition Thread Take-up Levers (Link Type) of Sewing Machines for Inoustrial Use 工業用縫紉機連桿式挑線桿 |
![]() |
|
|
CNS 13635
2017 Edition Steel Butt-welding Pipe Fittings for Ordinary Use 一般配管用鋼製對接銲接式管件 |
![]() |
|
|
CNS 773
2017 Edition Method of Test for Clear Varnish for Baking Varnish 烤漆用透明清漆檢驗法 |
![]() Translated |
|
|
CNS 15520
2017 Edition Push and Pull Drain Trap (P Type) 建築物室內用補平塗材 |
![]() |
|
|
CNS 12886-1
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法─120℃或150℃乾熱處理 |
![]() Translated |
|
|
CNS 3805
2017 Edition Range Hood 抽油煙機 |
![]() Translated |
|
|
CNS 4170
2017 Edition Short Pitch Transmission Precision Roller Chains anD Chain Wheels 短節距精確傳動滾子鏈條及鏈輪 |
![]() |
|
|
CNS 4646
2017 Edition Square Taper Washers for High Prestressed I-Sections 斜墊圈(工字鐵高強度結構用) |
![]() |
|
|
CNS 5376-4
2017 Edition Iron ores—Method for determination of combined water content 鐵礦石—結合水定量法 |
![]() |
|
|
CNS 10795
2017 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計(發電機式) |
![]() |
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法(使用抗張強度試驗機) |
![]() Translated |
|
|
CNS 15481-4
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads 道路車輛-電機電子配備環境條件與試驗-第4部:氣候負載 |
![]() |
|
|
CNS 6152
2017 Edition Method of Test for Electromechanical Switches(Electrical Endurance) 電機開關檢驗法–電耐久性 |
![]() |
|
|
CNS 660
2017 Edition Method of Test for Head Loss of Water Pumps 水泵工作位差檢驗法 |
![]() |
|
|
CNS 13982-3
2017 Edition Methods of test for bulk down and feather − Part 3: Composition (content analysis) 羽絨羽毛試驗法-第3部:組成 |
![]() |
|
|
CNS 4896
2017 Edition Accuracy Inspection of Metal Cutting Vertical Band Sawing Machines 立式帶鋸機精度檢驗標準 |
![]() Translated |
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
![]() |
|
|
CNS 4878
2017 Edition Dimensions of Solid Tires for Industrial Vehicles 工業車輛用實心輪胎之尺度 |
![]() Translated |
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for Indication) 發光二極體(指示用) |
![]() |
|
|
CNS 3183
2017 Edition Method of test for residues in liquefied petroleum gases 液化石油氣殘餘物試驗法 |
![]() |
|
|
CNS 7149
2017 Edition Steel Castings for Low Temperature and High Pressure Service 低溫高壓用鑄鋼件 |
![]() |
|
|
CNS 502
2017 Edition ISO Metric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5(ISO制)(標稱直徑12至80公釐,螺距1.5公釐) |
![]() |
|
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器-第11部:助聽器及相關設備之符號及標示 |
![]() |
|
|
CNS 4663
2017 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽(片封式,嵌於塑膠製品內) |
![]() |
Find out:13340Items | To Page of: First -Previous-Next -Last | [277] [278] [279] [280] [281] [282] [283] |