"D C " CNS Standards List |
|
CNS 4170
2017 Edition Short Pitch Transmission Precision Roller Chains anD Chain Wheels 短節距精確傳動滾子鏈條及鏈輪 |
![]() |
|
|
CNS 13635
2017 Edition Steel Butt-welding Pipe Fittings for Ordinary Use 一般配管用鋼製對接銲接式管件 |
![]() |
|
|
CNS 3805
2017 Edition Range Hood 抽油煙機 |
![]() Translated |
|
|
CNS 225
2017 Edition Shell Drills (Shell Counterborer) of High Speed Steel 殼形擴孔鑽 |
![]() |
|
|
CNS 5492
2017 Edition Thread Take-up Levers (Link Type) of Sewing Machines for Inoustrial Use 工業用縫紉機連桿式挑線桿 |
![]() |
|
|
CNS 15604
2017 Edition Corrugated stainless steel tubes for water supply 自來水用不銹鋼波狀管 |
![]() Translated |
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
![]() |
|
|
CNS 4573
2017 Edition Slotted RaiseD Countersunk Bolts for Drawing Instruments 有槽扁圓頂埋頭螺栓(繪圖儀器用) |
![]() |
|
|
CNS 744
2017 Edition Testing Standard for Rubber Rollers of Rice 碾米 |
![]() Translated |
|
|
CNS 6155
2017 Edition Method of Test for Electromechanical Switches(Actuator/Mounting Bushing Resistance) 電機開關檢驗法–主動器、裝架襯套電阻值 |
![]() |
|
|
CNS 13068
2017 Edition Methods of test for total amine values of amine-based hardeners of epoxy resins 環氧樹脂之胺系硬化劑總胺價試驗法 |
![]() Translated |
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
![]() |
|
|
CNS 5666
2017 Edition Spindle Noses for Milling Machines 銑床主軸鼻端 |
![]() |
|
|
CNS 4250
2017 Edition Square Head Screws with Collar and Half Dog Point with Rounded End Screws 軸環半柱端方頭螺釘 |
![]() |
|
|
CNS 6632
2017 Edition Household polyvinyl chloride gloves 家庭用聚氯乙烯塑膠手套 |
![]() |
|
|
CNS 5376-4
2017 Edition Iron ores—Method for determination of combined water content 鐵礦石—結合水定量法 |
![]() |
|
|
CNS 10795
2017 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計(發電機式) |
![]() |
|
|
CNS 13982-3
2017 Edition Methods of test for bulk down and feather − Part 3: Composition (content analysis) 羽絨羽毛試驗法-第3部:組成 |
![]() |
|
|
CNS 4646
2017 Edition Square Taper Washers for High Prestressed I-Sections 斜墊圈(工字鐵高強度結構用) |
![]() |
|
|
CNS 4663
2017 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽(片封式,嵌於塑膠製品內) |
![]() |
|
|
CNS 502
2017 Edition ISO Metric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5(ISO制)(標稱直徑12至80公釐,螺距1.5公釐) |
![]() |
|
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器-第11部:助聽器及相關設備之符號及標示 |
![]() |
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法(使用抗張強度試驗機) |
![]() Translated |
|
|
CNS 4878
2017 Edition Dimensions of Solid Tires for Industrial Vehicles 工業車輛用實心輪胎之尺度 |
![]() Translated |
|
|
CNS 3183
2017 Edition Method of test for residues in liquefied petroleum gases 液化石油氣殘餘物試驗法 |
![]() |
|
|
CNS 15481-4
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads 道路車輛-電機電子配備環境條件與試驗-第4部:氣候負載 |
![]() |
|
|
CNS 7149
2017 Edition Steel Castings for Low Temperature and High Pressure Service 低溫高壓用鑄鋼件 |
![]() |
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
![]() |
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for Indication) 發光二極體(指示用) |
![]() |
|
|
CNS 12864
2017 Edition Information and documentation - International standard book number (ISBN) 國際標準書號 |
![]() |
Find out:13340Items | To Page of: First -Previous-Next -Last | [277] [278] [279] [280] [281] [282] [283] |