"D " CNS Standards List |
|
CNS 6113
2017 Edition Boxes anD Covers for Unplasticized Polyvinyl Chloride Conduit 導電線用聚氯乙烯塑膠硬質管接線盒及蓋 |
|
|
|
CNS 13288
2017 Edition Basic Environmental Testing ProceDures Part 2: Tests - Guidance on Change of Temperature Tests 環境試驗法（電氣、電子）–溫度變化試驗之指引 |
|
|
|
CNS 11570
2017 Edition Remote Control Relays anD Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 305
2017 Edition HanD Taps for Whitworth Pipe Threads 絲公，手用，適於韋氏管子螺紋 |
Translated |
|
|
CNS 517
2017 Edition Metric Buttress Screw ThreaD, Allowance and Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 7999
2017 Edition Oil TempereD Chromium Silicon Alloy Steel Wires for Valve Springs 閥彈簧用油回火矽鉻合金鋼鋼線 |
|
|
|
CNS 12865-9
2017 Edition MethoD of Test for Digital Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 3983
2017 Edition MethoD of Test for Mechanical Properties of Tapping Screws 自攻螺釘之機械性質檢驗法 |
Translated |
|
|
CNS 14137
2017 Edition MethoD of eddy current test for titanium pipes and tubes 鈦管渦電流檢測法 |
|
|
|
CNS 10695
2017 Edition MethoD of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 15581
2017 Edition GraDing rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 12728
2017 Edition ExpanDed Steels 切擴鋼網 |
Translated |
|
|
CNS 15077-10
2017 Edition Test conDitions for machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－ 第10部：熱變形之評估 |
|
|
|
CNS 9243
2017 Edition MethoD of Test for Low Frequency(Below 3 MHz) Electrical Connectors(TP - 43 Cable Clamping (Bending Moment)) 頻率３ＭＨｚ以下電連接器檢驗法（彎曲試驗ＴＰ–４３） |
|
|
|
CNS 13652
2017 Edition Reliability Testing for Light Emitting Diode(for Communication) 通信用發光二極體之可靠度測試 |
|
|
|
CNS 15551-2
2017 Edition Ergonomics - Accessible Design - Sound pressure levels of auditory signals for consumer products 人因工程－無障礙設計 - 消費 產品中聲音訊號之聲壓位準 |
|
|
|
CNS 2534
2017 Edition MethoD of Test for Natural Rubber Latex 天然橡膠乳液檢驗法 |
Translated |
|
|
CNS 178
2017 Edition Flat FitteD Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 13580
2017 Edition MethoD of Test for Fire Hydrant Valves 消防栓閥檢驗法 |
|
|
|
CNS 307
2017 Edition Metric Taps for Hole, CylinDrical Shank and Square Head 穿透絲公，方頭長圓柱柄，適於公制螺紋 |
Translated |
|
|
CNS 4578
2017 Edition BolteD Connections with Reduced Booy; Metric Thread with Large Clearence, Nominal Values and Limits 減徑柄螺栓之結合法–具大間隙之公制螺紋（標稱尺寸與限界尺寸） |
|
|
|
CNS 744
2017 Edition Testing StanDard for Rubber Rollers of Rice 碾米 |
Translated |
|
|
CNS 9104
2017 Edition Symbols of Meters of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖計器類符號 |
|
|
|
CNS 660
2017 Edition MethoD of Test for Head Loss of Water Pumps 水泵工作位差檢驗法 |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability AssureD Fixed Carbon Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 15832-2-2
2017 Edition MethoD of test for coating components − Part 2-2: Component analysis in solvent soluble matter − Softening point (Ring-and-ball method) 塗料成分試驗法－第2-2部：溶劑可溶物中成分分析－軟化點(環與球法) |
|
|
|
CNS 8081
2017 Edition MethoDs of Performance Test of Panels for Building Construction 建築用組件（嵌板）性能檢驗法 |
|
|
|
CNS 4560
2017 Edition Cross RecesseD Countersunk (Flat) Head Screws 十字穴平頂埋頭螺釘 |
Translated |
|
|
CNS 14369
2017 Edition Micrographics-ReaDer-printers for transparent microforms-Characteristics 微縮技術－透明微縮品閱讀影印機－特性 |
|
|
|
CNS 11942-5
2017 Edition MethoDs for determination of manganese in copper and copper alloys 銅及銅合金中錳定量法 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [278] [279] [280] [281] [282] [283] [284] |
