"d " CNS Standards List| Gear Tooth | Mechanical shock | Calculation Load | Methods test | Feather edge | Method test | Method Test | Walking aids | |
|
CNS 9478
2017 Edition Method of Test for Thermoelectric Type High-Frequency Ampere Meter for Panel 盤用熱電型高頻電流表檢驗法 |
|
|
|
CNS 14557
2017 Edition Method of reliability test for road traffic LED display panel 道路用發光二極體文字顯示型交通資訊看板之可靠度測試 |
|
|
|
CNS 3453
2017 Edition Method of test for milk and milk products - Test of the residual antimicrobial substances in raw milk 乳品檢驗法－生乳中抗生物質殘留之檢驗 |
|
|
|
CNS 12296
2017 Edition Reliability Assured Power Type Fixed Wire Wound Resistors (S) (Established Failure Rate) 可靠度保證功率型線繞固定電阻器（特性Ｓ）（故障率設定） |
Translated |
|
|
CNS 3723
2017 Edition Method of test for milk and milk products - Determination of chloride content in edible cheese 乳品檢驗法－食用乾酪氯化物含量之測定 |
|
|
|
CNS 4696
2017 Edition Round Head Nip Bolts 圓頭單鰭螺栓 |
|
|
|
CNS 1016
2017 Edition Picks, One Conical End and One Flat End 十字鎬（一端為斜錐狀，一端為扁平狀） |
|
|
|
CNS 13165
2017 Edition Method of Macro Test for Section of Spot Welded Joints 點熔接接合之斷面巨觀試驗法 |
|
|
|
CNS 15210-3
2017 Edition Information technology - Radio frequency identification for item management - Part 3: Parameters for air interface communications at 13.56MHz 資訊技術－品項管理之無線射頻識別－第３部：１３.５６ＭＨｚ空中介面通信參數 |
|
|
|
CNS 13330
2017 Edition dynamo Lamp for Bicycles 自行車（腳踏車）用發電燈 |
|
|
|
CNS 662
2017 Edition Method of Test for Rotational Speed of Water Pumps 水泵轉速檢驗法 |
|
|
|
CNS 13331
2017 Edition Sound Calibrator 音壓校正器 |
|
|
|
CNS 12662
2017 Edition Method of Test for Qualification Procedure of Gas Pressure Welding Technique 鑑定氣體壓力熔接技術之試驗法 |
|
|
|
CNS 4946
2017 Edition Clamping Screws for drawing Instruments 製圖儀器用夾緊螺釘 |
|
|
|
CNS 3592
2017 Edition Nickel and nickel alloy covered electrodes 鎳及鎳合金被覆銲條 |
|
|
|
CNS 3908
2017 Edition Method of Test for Wiring Devices 配線器具之試驗法 |
|
|
|
CNS 12248
2017 Edition Methods of Test for Pressure-sensitive Adhesive Tapes for Electrical Insulation 電絕緣用黏帶試驗法 |
|
|
|
CNS 6876
2017 Edition Spindle Noses and Face Plates of Lathes 車床之主心軸鼻端及面板 |
|
|
|
CNS 4358
2017 Edition Slotted Pan Head Screws with Shoulder 有槽盤頭有肩螺釘 |
Translated |
|
|
CNS 7351
2017 Edition Spades 一般鏟 |
|
|
|
CNS 4851
2017 Edition Screwed Sealing Plugs for Drain Fittings of High Density PE 螺旋塞（用於排水配件者，硬質聚乙烯製） |
|
|
|
CNS 5376-6
2017 Edition Iron ores—Method for determination of acid soluble iron （Ⅱ）content 鐵礦石－酸可溶性鐵（Ⅱ）定量法 |
|
|
|
CNS 14492-6
2017 Edition Methods of measurement on radio receivers for various classes of emission -Part 6：General purpose communication receivers 不同發射類別之無線電接收機的量測方法─第６部：一般用途通訊接收機 |
|
|
|
CNS 5376-20
2017 Edition Iron ores－Methods for determination of tin content 鐵礦石－錫定量法 |
|
|
|
CNS 10865
2017 Edition Method of test for alpha-, beta- and gamma- cellulose in pulp 紙漿中α-、β-、γ- 纖維素試驗法 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 14659
2017 Edition Acoustics - determination of sound power levels of noise sources using sound pressure - Comparison method in situ 聲學─利用聲壓測定噪音源聲功率位準─現場的比較法 |
|
|
|
CNS 13212
2017 Edition Surface Acoustic Wave (SAW) Resonators Part 1: General Information and Standard Values 表面聲波諧振器 第一部：一般性資訊及標準值 |
|
|
|
CNS 4552
2017 Edition Rounded Trapezoidal Thread; Nominal Sizes 圓角梯形螺紋（標稱尺寸） |
|
|
|
CNS 9202
2017 Edition Method for Determining Flow Rate of Metal Powders 金屬粉末流動度測定法 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [287] [288] [289] [290] [291] [292] [293] |
