"a, " CNS Standards List| Information technology | Corrosion metals | Water flow | Parallel Shank | Sands buildings | Method Test | Autocatalytic Nickel | Method test | |
|
CNS 1261
2017 Edition Safety Code for Steel Cylinder of Highly Compressed Oxygen 高壓氧氣鋼瓶安全規章 |
|
|
|
CNS 14866-2
2017 Edition Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 10901
2017 Edition Method of Test for Terminal Blocks for Industrial and Similar Use 工業用接線板檢驗法 |
|
|
|
CNS 12854
2017 Edition Fire Fighting Equipment for Liquefied Petroleum Gas Plant Use 液化石油氣設施用消防設備 |
|
|
|
CNS 6410
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算–小齒輪單齒接觸因數Ｚв 、大齒輪單齒接觸因數Ｚᴅ及正面接觸比 ε⍺ |
|
|
|
CNS 10015
2017 Edition Glossary of terms relating to dynamic properties of vulcanized rubber 硫化橡膠動態性質用語 |
|
|
|
CNS 8785
2017 Edition Method of Test for Electric Strength of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管絕緣強度試驗法 |
|
|
|
CNS 66
2017 Edition Square Heads and Holes (for Shaft, Hand Wheel and Handles) 方頭及方孔（用於軸，手輪及手柄） |
|
|
|
CNS 15466
2017 Edition Testing method of performance for air source heat pump water heaters 空氣源式熱泵熱水器之性能試驗法 |
|
|
|
CNS 3886
2017 Edition Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理 |
Translated |
|
|
CNS 4069
2017 Edition Pneumatic fluid power − General rules and safety requirements for systems and their components 氣動輪磨機 |
Translated |
|
|
CNS 195
2017 Edition Liquid carbon dioxide 液態二氧化碳 |
|
|
|
CNS 14671
2017 Edition Manipulating industrial robots － EMC test methods and performance evaluation criteria － Guidelines 工業用機器人－電磁相容性試驗方法及性能評估準則－指引 |
|
|
|
CNS 9369
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 35 Proposed Insert Retention) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入扣鎖ＴＰ–３５） |
|
|
|
CNS 11446-6
2017 Edition Methods of measurement on receivers for television broadcast transmission - Part 6 : Measurement under conditions different from broadcast signal standards 電視廣播傳輸接收機之量測方法-第6部 : 不同於廣播信號標準條件之量測 |
|
|
|
CNS 6183
2017 Edition Light gauge steels for general structures 一般結構用輕型鋼 |
|
|
|
CNS 14674-1
2017 Edition Electromagnetic compatibility (EMC) - Generic standards - Part 1: Immunity for residential, commercial and light - industrial environments 電磁相容性（ＥＭＣ）－一般性標準－第１部：住宅、商業與輕工業環境之免疫力 |
|
|
|
CNS 15492
2017 Edition Toothpastes (Dentifrices) 牙膏與牙粉 |
|
|
|
CNS 13416
2017 Edition Method of Sampling of Fillers and Pigments for Paper Making 造紙用填料及顏料採樣法 |
Translated |
|
|
CNS 5376-3
2017 Edition Iron ores—Method for determination cobalt content 鐵礦石—鈷定量法 |
|
|
|
CNS 15347
2017 Edition Safety of machinery − General principles for design − Risk assessment and risk reduction 機械安全－設計之一般原則－風險評鑑及風險降低 |
|
|
|
CNS 6409
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算–材料因數Zм |
|
|
|
CNS 12884
2017 Edition Method of sampling and preparing wood for general analysis and preparation of wood for chemical analysis 紙漿用木材取樣與調製法及化學分析用木材之製備法 |
|
|
|
CNS 3434
2017 Edition Crimp-Type Terminal Lugs Copper Conductors 銅線用壓著端子 |
Translated |
|
|
CNS 16014
2017 Edition Interconnection protocol for devices in smart home 智慧家庭之裝置互連協定 |
|
|
|
CNS 12112
2017 Edition Lighting of indoor work places 室內工作場所照明 |
|
|
|
CNS 7194
2017 Edition Single-start solid (monobloc) gear hobs with tenon drive or axial keyway, modules 1 to 40-Nominal dimensions 具有榫槽或鍵槽之單紋螺紋滾齒刀﹝模數１至４０﹞─標稱尺度 |
|
|
|
CNS 442
2017 Edition Classification of timber 木材之分類 |
|
|
|
CNS 4878
2017 Edition Dimensions of Solid Tires for Industrial Vehicles 工業車輛用實心輪胎之尺度 |
Translated |
|
|
CNS 7407
2017 Edition Cellular plastics and rubbers - Determination of apparent (bulk) density 發泡塑膠及橡膠－視密度測定法 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [293] [294] [295] [296] [297] [298] [299] |
