"a, " CNS Standards List |
|
CNS 3434
2017 Edition Crimp-Type Terminal Lugs Copper Conductors 銅線用壓著端子 |
Translated |
|
|
CNS 4939
2017 Edition Tar epoxy resin paint 環氧樹脂柏油漆 |
|
|
|
CNS 5770
2017 Edition General Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 11226
2017 Edition Radiographic Test for Carbon Steel Weldment 碳鋼熔接件射線檢測法 |
|
|
|
CNS 11609
2017 Edition Method of Test for Unplasticized Polyvinyl Chloride Pipes with Fiberglass Reinforced Plastic Reinforcement 玻璃纖維強化塑膠加強聚氯乙烯塑膠硬質管檢驗法 |
Translated |
|
|
CNS 5285
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 304
2017 Edition Hand Taps, Metric (Two Pieces Per Set) 公制絲公，手用，每套兩件 |
Translated |
|
|
CNS 1298
2017 Edition Unplasticized polyvinyl chloride (PVC-U) pipes 硬質聚氯乙烯塑膠管 |
Translated |
|
|
CNS 8784
2017 Edition Method of Test for Tensile of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管拉伸試驗法 |
|
|
|
CNS 14694-3
2017 Edition Audio , video and audiovisual systems- interconnections and matching values Part 3：Interface for the interconnection ENG cameras and portable VTRs using non-composite signals 聲音、影像及視聽系統之互連與匹配值－第３部：ＥＮＧ攝影機與可攜式ＶＴＲｓ使用非複合式信號互連之介面 |
|
|
|
CNS 13982-2
2017 Edition Methods of test for bulk down and feather − Part 2: Sampling 羽絨羽毛試驗法－第2部：抽樣 |
|
|
|
CNS 5376-5
2017 Edition Iron ores—Methods for determination of total iron content 鐵礦石—總鐵定量法 |
|
|
|
CNS 8910
2017 Edition Methods of exposure to laboratory light sources for polymeric material of buildings 建築用聚合材料實驗室光源曝露試驗法 |
|
|
|
CNS 14645
2017 Edition Light gauge stainless steel pipe fittings for ordinary piping 一般配管用不銹鋼鋼管接頭 |
|
|
|
CNS 3886
2017 Edition Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理 |
Translated |
|
|
CNS 95
2017 Edition Accuracy Inspection of Upright Drilling Machines 直立鑽床精度檢驗 |
Translated |
|
|
CNS 444
2017 Edition Grading rules for sawn lumber 製材之分等 |
|
|
|
CNS 6407
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算-負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 6834-9
2017 Edition Testing methods for rubber and plastics hoses - Part 9: Bending properties of hoses and tubing 橡膠管及塑膠管試驗法－第9部：膠管及軟管之彎曲特性 |
|
|
|
CNS 12896
2017 Edition Pressure Rating for Ferrous Material Pipe Flanges 氣體熔接、截割（切斷）用壓力調整器 |
|
|
|
CNS 11225
2017 Edition Liquid Penetrant Test for Castings 鑄件表面液滲檢驗法 |
|
|
|
CNS 4028
2017 Edition Mechanical properties of nuts-Effective heights of thread ≧0.4d 螺帽之機械性質（有效螺紋長度在0.4d以上者） |
|
|
|
CNS 14466-8
2017 Edition Audiovisual,video and television equipment and systems. Part8:Syinbols and identification 視聽．影像及電視設備與系統-第８部：符號標誌與識別 |
|
|
|
CNS 2215
2017 Edition Particleboards 粒片板 |
|
|
|
CNS 11659
2017 Edition Method of Test for Construction Parts of Glassfiber Reinforced Plastic Septic Tank 玻璃纖維強化塑膠化糞槽體檢驗法 |
Translated |
|
|
CNS 12298
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP-53 Nitric Acid Vapor Test, Gold Finish) 頻率３ＭＨｚ以下電連接器檢驗法（硝酸氣試驗，鍍金接點ＴＰ–５３） |
|
|
|
CNS 5535
2017 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 5298
2017 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 4053-1
2017 Edition Unplasticized polyvinyl chloride (PVC-U) pipes for water supply 自來水用硬質聚氯乙烯塑膠管 |
Translated |
|
|
CNS 5277
2017 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [293] [294] [295] [296] [297] [298] [299] |
