"Plastic " CNS Standards List| Hand Lift | Wood – | Method test | Integrated circuits | Recommendation Lighting | Switchgears, Contact | Biological evaluation | Test Code | |
|
CNS 2456-2
2020 Edition Plastics piping systems for water supply and for drainage and sewerage under pressure − Polyethylene (PE) − Part 1: General 壓力下給水、排水及排污用塑膠配管系統—聚乙烯(PE)—第2部：管 |
|
|
|
CNS 3553
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of tensile stress-strain properties 硫化或熱塑性橡膠－拉伸應力－應變性質之測定 |
|
|
|
CNS 3655
2020 Edition Method for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency 水硬性水泥可塑稠性水泥漿及墁料之機械拌合法 |
|
|
|
CNS 12780
2020 Edition Method of test for flexural properties of glass fiber reinforced Plastics 玻璃纖維強化塑膠之抗曲性能測定法 |
|
|
|
CNS 3562
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of the effect of liquids 硫化或熱塑性橡膠－耐液性測定法 |
|
|
|
CNS 2456-3
2020 Edition Plastics piping systems for water supply and for drainage and sewerage under pressure − Polyethylene (PE) − Part 2: Pipes 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 13474
2020 Edition Acrylonitrile - Butadiene - Styrene (ABS) Plastic Pipes and Fittings for Chemical Industrial and General Uses 化學工業及一般用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管及接頭配件 |
|
|
|
CNS 2456-5
2020 Edition Plastics piping systems for water supply and for drainage and sewerage under pressure − Polyethylene (PE) − Part 3: Fittings 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 10019
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of compression stress-strain properties 硫化或熱塑性橡膠壓縮應力－應變性質測定法 |
|
|
|
CNS 2456-1
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 5: Fitness for purpose of the system 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第1部：通則 |
|
|
|
CNS 15361
2020 Edition Determination of the ultimate anaerobic biodegradation and disintegration under high-solids anaerobic-digestion conditions of Plastics - Method by analysis of released biogas 塑膠材料在高固體厭氧消化環境下最終厭氧生物分解性與崩解性測定法－釋出生物生成氣體分析法 |
|
|
|
CNS 3561
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of rebound resilience 硫化或熱塑性橡膠－回彈性測定法 |
|
|
|
CNS 15363
2020 Edition Determination of the ultimate aerobic biodegradability of Plastics in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved 藉由量測呼吸計內需氧量或二氧化碳釋出量測定土壤中塑膠之好氧生物分解度 |
|
|
|
CNS 15258
2020 Edition Biodegradable Plastics used as coatings on paper and other compostable substrates 用於紙與其他可堆肥基質覆層之生物可分解塑膠 |
|
|
|
CNS 12835-3
2020 Edition Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) − Part 2: Pipes 燃氣用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 12835-5
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 4: Valves 燃氣用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 9352
2020 Edition Bushes for Plain Bearings Made From Dura Plastics 滑動軸承軸襯–熱硬性樹脂製 |
|
|
|
CNS 12244
2020 Edition General Requirements for Construction of Plastics Injection Molding Machines 塑膠射出成型機構造準則 |
|
|
|
CNS 11908
2020 Edition Plastic Bobbins for Ring Spinning Flame 低壓電表用塑膠箱體及固定板 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 13158
2020 Edition Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipes for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管 |
Translated |
|
|
CNS 10016-1
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of dynamic properties − Part 1: General guidance 硫化或熱塑性橡膠動態性質之測定第1部：一般指引 |
|
|
|
CNS 7050
2020 Edition Method of test for time-to-failure of Plastic pipe under constant internal pressure 塑膠管在內部恆壓下之破壞時間試驗法 |
|
|
|
CNS 9354
2020 Edition Bushes for Plain Bearings, Press Bushes Made From ThermoPlastics 滑動軸承軸襯–熱塑性塑膠製 |
|
|
|
CNS 15823
2020 Edition Measurement of antibacterial activity on Plastics and other non-porous surfaces 塑膠及非多孔表面抗菌性測定法 |
|
|
|
CNS 3564-2
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of low-temperature properties − Part 2: Determination of low-temperature brittleness 硫化或熱塑性橡膠－低溫性質之測定－第2部：低溫脆性測定法 |
|
|
|
CNS 3564-3
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of low-temperature properties − Part 3: Determination of low temperature stiffening (Gehman test) 硫化或熱塑性橡膠−低溫性質之測定－第3部：低溫剛度測定法(吉門試驗) |
|
|
|
CNS 3564-4
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of low-temperature properties − Part 4: Determination of low-temperature retraction (TR test) 硫化或熱塑性橡膠－低溫性質之測定－第4部：低溫回縮測定法(TR試驗) |
|
|
|
CNS 15320
2020 Edition Determination of the ultimate anaerobic biodegradation of Plastic materials in an aqueous system - Method by measurement of biogas production 塑膠材料在水溶液系統中最終厭氧生物分解度測定法－生物生成氣體量測法 |
|
|
|
CNS 14306-3
2020 Edition Preparation of Specimens for Optical Tests on Plastics Materials-Moulding Method 塗料及有關製品塗裝前之鋼面處理－噴射清理鋼面之表面粗糙度特性（ISO表面輪廓參比標準板校正方法及剖面曲線測定法－調焦顯微鏡法） |
|
| Find out:452Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 |
