": " CNS Standards List |
|
CNS 9315
2019 Edition Method of Test for Feed Additives: Determination of Arsanilic Acid 飼料添加物檢驗法–胺苯亞砷酸之測定 |
|
|
|
CNS 61347-2-13
2019 Edition Lamp controlgear − Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules 光源控制裝置－第2-13部：LED模組用直流或交流電子式控制裝置之個別要求 |
|
|
|
CNS 62282-7-2
2019 Edition Fuel cell technologies − Part 7-2: Test methods − Single cell and stack performance tests for solid oxide fuel cells (SOFC) 燃料電池技術－第7-2部：試驗方法－固態氧化物燃料電池(SOFC)單電池及電池組性能試驗 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 13306-2-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power 射頻擾動和免疫力量測設備與量測方法－第２－２部：擾動和免疫力量測方法－擾動功率量測 |
|
|
|
CNS 14873-3
2019 Edition Road vehicles - Airbag components - Part 3: Testing of inflator assemblies 道路車輛－氣囊組件－第３部：充氣器 |
|
|
|
CNS 15251-3
2019 Edition Information technology − Open document format for office applications (OpenDocument) v1.2 − Part 3: Packages 資訊技術－辦公室應用軟體OpenDocument v1.2 之開放文件格式－第3部：套件 |
|
|
|
CNS 7779-3
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions − Part 3: Enveloping surface methods 工業用風機－在標準化實驗室條件下風機聲功率位準測定－第3 部：包絡面法 |
|
|
|
CNS 16093-3
2019 Edition Welding and allied processes − Types of joint preparation − Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys 銲接及其相關製程－接頭準備型式－第3部：鋁及鋁合金的惰氣遮護金屬電弧銲接及惰氣遮護鎢極電弧銲接 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 15593-31
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 31: Use of local area networks on twisted pair with carrier signalling 電力計量－ 讀表、計費及負載控制之資料交換－ 第31 部： 使用雙絞線載波信號之區域網路 |
|
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 14545-5
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 15142
2019 Edition Textiles - Determination of fabric propensity to surface fuzzing and to pilling : Modified Martindale method 紡織品起毬檢驗法－改良馬丁代爾法 |
|
|
|
CNS 15130-2-2
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 60335-2-7
2019 Edition Household and similar electrical appliances − Safety − Part 2-7: Particular requirements for washing machines 家用和類似用途電器－安全性－第2-7 部：洗衣機之個別規定 |
|
|
|
CNS 15755-5-8
2019 Edition Conversion tables for units − Part 5-8: Pressure or stress − Kilopascal and millimeter of mercury 單位換算表－第5-8 部：壓力或應力－千帕斯卡與毫米汞柱 |
|
|
|
CNS 15748-2
2019 Edition Integrated circuits – Measurement of electromagnetic emissions, 150 kHz to 1 GHz − Part 2: Measurement of radiated emissions − TEM cell and wideband TEM cell method 積體電路－ 150 kHz 至1 GHz 電磁放射量測－第2 部： 輻射放射量測－ 橫向電磁波室與寬頻橫向電磁波室法 |
|
|
|
CNS 13306-2-4
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-4: Methods of measurement of disturbances and immunity - Immunity measurements 射頻擾動和免疫力量測設備與量測方法－第２－４部：擾動和免疫力量測方法－免疫力量測 |
|
|
|
CNS 13306-1-4
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances 射頻擾動和免疫力量測設備與量測方法－第１－４部：射頻擾動和免疫力量測設備－輔助設備－輻射擾動 |
|
|
|
CNS 15141
2019 Edition Textiles - Determination of fabric propensity to surface fuzzing and to pilling : Pilling box method 紡織品起毬檢驗法－盒型起毬試驗法 |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 12514-4
2019 Edition Fire-resistance tests – Elements of building construction – Part 4: Specific requirements for loadbearing vertical separating elements 建築物構造構件耐火試驗法－第4 部：承重垂直區劃構件特定要求 |
|
|
|
CNS 15764-4
2019 Edition Footwear − Test methods for insoles – Part 4: Resistance to stitch tear of insoles 鞋類－中底板試驗法－第4 部：中底板之耐針縫撕裂強度 |
|
|
|
CNS 9026
2019 Edition Method of Test for Feed Additives: Determination of Nystatin 飼料添加物檢驗法–寧畜定之測定 |
|
|
|
CNS 14545-2
2019 Edition Fire hazard testing-part 1:Guidance for the preparation of requirements and test specifications for assessing fire hazard of electrotechnical products-Guidance for electronic components 火災危險性試驗－第１部：制定評估電氣產品之火災危險性需求及試驗內容之指引－電子零組件之指引 |
|
|
|
CNS 5346-2
2019 Edition Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials 塑膠－縮寫用語與符號（第３部：可塑劑） |
|
|
|
CNS 15077-6
2019 Edition Test conditions for machining centers - Part 6 : Accuracy of feeds, speeds and interpolations 切削中心機之檢驗條件－第６部：進給、速率與插值之精度 |
|
|
|
CNS 15748-3
2019 Edition Integrated circuits − Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 3: Measurement of radiated emissions – Surface scan method 積體電路－150 kHz 至1 GHz 電磁放射量測－第3 部：輻射放射量測－表面掃描法 |
|
| Find out:2437Items | To Page of: First -Previous-Next -Last | [25] [26] [27] [28] [29] [30] [31] |
