"Part " CNS Standards List |
|
CNS 15130-2-2
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 16094-1
2019 Edition Ductile iron pipes, fittings, accessories and their joints − External zinc-based coating − Part 1: Metallic zinc with finishing layer 延性鑄鐵管、管件、配件及接頭－外部鋅基塗層－第1部：金屬鋅及精整層 |
|
|
|
CNS 62282-7-2
2019 Edition Fuel cell technologies − Part 7-2: Test methods − Single cell and stack performance tests for solid oxide fuel cells (SOFC) 燃料電池技術－第7-2部：試驗方法－固態氧化物燃料電池(SOFC)單電池及電池組性能試驗 |
|
|
|
CNS 15646-1
2019 Edition Rigid cellular plastics – Determination of flexural properties – Part 1: Basic bending test 硬質發泡塑膠－彎曲性能測定法－第1 部：基本彎曲試驗 |
|
|
|
CNS 15753
2019 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 7: Guidance for the assessment of conformity 地下排水及排污非壓力塑膠配管系統－聚乙烯(PE) |
|
|
|
CNS 15200-9-2
2019 Edition Methods of test for paints – Part 9-2: Coating powders – Inclined-plane flow test 塗料一般試驗法－第9-2 部：粉體塗料－斜面流動性試驗 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 61347-2-13
2019 Edition Lamp controlgear − Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules 光源控制裝置－第2-13部：LED模組用直流或交流電子式控制裝置之個別要求 |
|
|
|
CNS 15659-2
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles − Part 2: Moisture management test 紡織品吸濕速乾性能評估－第2 部：水分傳導試驗法 |
|
|
|
CNS 15755-5-8
2019 Edition Conversion tables for units − Part 5-8: Pressure or stress − Kilopascal and millimeter of mercury 單位換算表－第5-8 部：壓力或應力－千帕斯卡與毫米汞柱 |
|
|
|
CNS 13306-2-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power 射頻擾動和免疫力量測設備與量測方法－第２－２部：擾動和免疫力量測方法－擾動功率量測 |
|
|
|
CNS 14545-4
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 0:Glow-wire test methods-General 火災危險性試驗－第２部：試驗方法－第１章／第０單元：熾熱線試驗方法－通則 |
|
|
|
CNS 15186-2
2019 Edition Cleanrooms and associated controlled environments – Part 2: Specifications for testing and monitoring to prove continued compliance with CNS 15186-1 潔淨室及其附屬之控制環境－第２部：確保持續符合ＣＮＳ １５１８６－１之測試與監測規範 |
|
|
|
CNS 15207-1
2019 Edition Road vehicles − Component test methods for electrical disturbances from narrowband radiated electromagnetic energy − Part 1: General principles and terminology 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第1 部:通則及用語 |
|
|
|
CNS 60245-8
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 8: Cords for applications requiring high flexibility 額定電壓450/750 V 以下橡膠絕緣電纜－第8部：高可撓性用途花線 |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 16120-1
2019 Edition Video surveillance system security − Part 1: General requirements 影像監控系統安全－第1部：一般要求事項 |
|
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 7779-3
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions − Part 3: Enveloping surface methods 工業用風機－在標準化實驗室條件下風機聲功率位準測定－第3 部：包絡面法 |
|
|
|
CNS 60335-2-7
2019 Edition Household and similar electrical appliances − Safety − Part 2-7: Particular requirements for washing machines 家用和類似用途電器－安全性－第2-7 部：洗衣機之個別規定 |
|
|
|
CNS 15125-2
2019 Edition Solar heating - Domestic water heating systems - Part 2 : Outdoor test methods for system performance characterization and yearly performance prediction of solar-only systems 太陽能加熱－家用熱水系統－第２部：僅用太陽能系統的性能特性與年度性能預測之室外試驗法 |
|
|
|
CNS 16083-2
2019 Edition Viscosity and viscometric fixed points of glass − Part 2: Determination of annealing point and strain point by fiber elongation 玻璃黏度和黏度固定點－第2部：以玻璃絲拉伸法測定退火點和應變點 |
|
|
|
CNS 15760-3
2019 Edition Footwear − General test methods – Part 3: Ageing conditioning 鞋類－一般試驗法－第3 部：老化調節 |
|
|
|
CNS 15076-2
2019 Edition Modular units for machine tools - Workholding pallets - Part 2 : Workholding pallets of nominal size greater than 800 mm 工具機之模組單元－工件固定托板－第２部：標稱尺度８００ｍｍ以上之工件固定托板 |
|
|
|
CNS 15748-3
2019 Edition Integrated circuits − Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 3: Measurement of radiated emissions – Surface scan method 積體電路－150 kHz 至1 GHz 電磁放射量測－第3 部：輻射放射量測－表面掃描法 |
|
|
|
CNS 15449-2-101
2019 Edition Safe requirements for electrical for measurement, control and laboratory use ? Part 2-101: Particular requirements for in vitro diagnostic (IVD) medical equipment 量測、控制及實驗室使用電氣設備安全規定－第2-101 部:體外診斷(IVD)醫用設備之個別規定 |
|
|
|
CNS 15194-2
2019 Edition Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 2: Off-vehicle radiation sources 道路車輛－來自窄頻輻射電磁能量的電擾動之車輛試驗法－第２部：車外輻射源 |
|
|
|
CNS 15077-6
2019 Edition Test conditions for machining centers - Part 6 : Accuracy of feeds, speeds and interpolations 切削中心機之檢驗條件－第６部：進給、速率與插值之精度 |
|
|
|
CNS 15762-5
2019 Edition Footwear − Test methods for uppers − Part 5: Thermal insulation of uppers, linings and insocks 鞋類－鞋面試驗法－第5 部：鞋面、內裡及鞋墊之隔熱性 |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [25] [26] [27] [28] [29] [30] [31] |
